Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: advmame, dos, and tbalde64 install  (Read 1258 times)

0 Members and 1 Guest are viewing this topic.

vincentc77

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 13
  • Last login:May 11, 2020, 08:14:22 pm
  • I want to build my own arcade controls!
advmame, dos, and tbalde64 install
« on: January 28, 2005, 10:03:26 am »
I'm finally getting all of the pieces and knowledge together inorder to try getting my 25kHz monitor to properly display the advcfg setup screen.  I'm going to try these steps tonight:

- set pclock at 5-90
- set hoz freg at 24.9 KHz
-set vetical freq at 47-63 Hz.
- play with shift 'i'
-increase/decrease horz freq by .01
-repeat until screen is viewable.

-Does anyone know if any special lines in the rc file  are needed for the tblade 64, or any TSRs?  Remeber this is for DOS using a WG U3000 EGA arcade monitor.   Anyone want to add anything?

Thanks,
Charlie
Logged

whammoed

  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2312
  • Last login:October 28, 2025, 03:59:04 pm
  • Crack don't smoke itself
    • NiceMite
Re: advmame, dos, and tbalde64 install
« Reply #1 on: January 28, 2005, 10:21:00 am »
Yes,
I thought the U3000 was a 31Khz monitor?
http://www.happcontrols.com/monitors/49083200.htm
 ???
Logged

vincentc77

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 13
  • Last login:May 11, 2020, 08:14:22 pm
  • I want to build my own arcade controls!
Re: advmame, dos, and tbalde64 install
« Reply #2 on: January 28, 2005, 11:23:41 am »
The model number is 33K3201, according to WG.  It was in an NFL Blitz cab which is an EGA game.

Charlie

Logged

Thenasty

  • Trade Count: (+17)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 4420
  • Last login:Today at 12:10:01 am
    • Thenasty's Arcademania Horizontal/Vertical monitor setup.
Re: advmame, dos, and tbalde64 install
« Reply #3 on: January 28, 2005, 11:55:06 am »
Quote from: vincentc77 on January 28, 2005, 11:23:41 am
The model number is 33K3201, according to WG.
Logged
Thenasty's Arcademania Horizontal/Vertical setup.
http://forum.arcadecontrols.com/index.php?topic=26696.0

Free VGA Breakout Cable
http://forum.arcadecontrols.com/index.php?topic=38228.0

Ultimate All in One Coin Mech write up (Make your own)
http://forum.arcadecontrols.com/index.php?topic=19200.0

whammoed

  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2312
  • Last login:October 28, 2025, 03:59:04 pm
  • Crack don't smoke itself
    • NiceMite
Re: advmame, dos, and tbalde64 install
« Reply #4 on: January 28, 2005, 12:03:45 pm »
I imagine it may be possible to adjust the horizontal frequency on that monitor to get it to sync with 25hz instead of 31hz.  I had a U3100 that you could adjust quite a bit/
Logged

rockmes

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 141
  • Last login:June 05, 2016, 09:41:38 am
  • Don't you love it?
Re: advmame, dos, and tbalde64 install
« Reply #5 on: January 30, 2005, 07:20:18 pm »
you will find what you need on this site- the tsr and the setting you need
http://easymamecab.mameworld.net/
Logged
Pages: [1]
  
Go Up
« previous next »