Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up --- Bug Reports --- Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: rowe 100 amp problem after replacing high output transister  (Read 951 times)

0 Members and 1 Guest are viewing this topic.

gmtransman2

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 13
  • Last login:December 24, 2019, 01:43:47 pm
  • I want to build my own arcade controls!
rowe 100 amp problem after replacing high output transister
« on: November 08, 2019, 11:01:29 pm »
so after all the reading on the amp i took the dive into fixing my amp. remove amp and found the 2 fuses blown on one drive board so replaced the transistors and the fuses. plugged back in and let the smoke out of a couple resisters on the driver board. fuses did no blow. any help would be great thanks

ami-man

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1083
  • Last login:January 22, 2020, 04:57:58 am
Re: rowe 100 amp problem after replacing high output transister
« Reply #1 on: November 27, 2019, 06:39:27 am »
Hello gmtransman2,

More than likely the two larger resistors were already overheated when the fuses and transistor failed.
Check these large fuses and other components on the board. If needs be obtain another driver board and recheck those transistors again, did you put the mica disks on the transistors when replacing them?

Regards
Alan Hood
ami-man
UK

gmtransman2

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 13
  • Last login:December 24, 2019, 01:43:47 pm
  • I want to build my own arcade controls!
Re: rowe 100 amp problem after replacing high output transister
« Reply #2 on: December 02, 2019, 10:40:11 pm »
yes i did put the mica under the transistor , is there a  good place to buy the transistors in pairs other than ebay. thanks

Ken Layton

  • Guru
  • Trade Count: (0)
  • Full Member
  • ****
  • Offline Offline
  • Posts: 6941
  • Last login:Today at 12:41:45 am
  • Technician
Re: rowe 100 amp problem after replacing high output transister
« Reply #3 on: December 03, 2019, 12:00:29 pm »
Bruce Wentworth at A & B Jukebox Repair sells the transistors. He specializes in Rowe jukeboxes.

https://www.abjukeboxrepair.com/

lilshawn

  • Trade Count: (+3)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6450
  • Last login:Yesterday at 11:43:35 pm
  • I break stuff...then fix it...sometimes
Re: rowe 100 amp problem after replacing high output transister
« Reply #4 on: December 16, 2019, 05:21:08 pm »
those pre-driver boards are pretty cheap (i've sen them for about 30 bucks a piece.) they have been redesigned several times to improve performance and reliability over the last 30 some odd years.... if you can find some new ones, it is worth it to replace them.