Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: Kade trackball support questions  (Read 1007 times)

0 Members and 1 Guest are viewing this topic.

jugger18

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 92
  • Last login:February 25, 2020, 09:58:30 am
  • Time to make a bitchen man cave
Kade trackball support questions
« on: February 10, 2015, 12:01:33 am »
I have some questions using the KADE as an encoder for a happ trackball.  I wired it as suggested by the encoder software.  If i flash it as a mouse Goldentee does not seem to see it.  If I flash as gamepad, GT sees it but it is hypersensitive and does not reset to zero when it stops spinning.  IS the support really just no there yet or am I doing something wrong?
Logged

bfauska

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1372
  • Last login:April 15, 2025, 10:49:31 pm
  • "You're not wrong Walter, you're just an @##hole!"
Re: Kade trackball support questions
« Reply #1 on: February 10, 2015, 01:35:03 am »
Have you made sure to turn on mouse support in mame? It seems like a silly question but I missed it just recently when I added a trackball to my cabinet. It was a setting in the mame.ini file.
Logged

PL1

  • Global Moderator
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9709
  • Last login:Today at 05:17:58 am
  • Designated spam hunter
Re: Kade trackball support questions
« Reply #2 on: February 10, 2015, 02:15:52 am »
Quote from: jugger18 on February 10, 2015, 12:01:33 am
I have some questions using the KADE as an encoder for a happ trackball.  I wired it as suggested by the encoder software.  If i flash it as a mouse Goldentee does not seem to see it.  If I flash as gamepad, GT sees it but it is hypersensitive and does not reset to zero when it stops spinning.  IS the support really just no there yet or am I doing something wrong?
Have you looked through the KADE Loader v1.1.2.0 release notes thread here.

Quote
Auto-centering can be enabled by keeping HWB pressed down (or by adding switch between HWB and ground

Not sure if it is possible to adjust sensitivity in the gamepad trackball firmware, but you can adjust the other one.


Scott
Logged

jugger18

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 92
  • Last login:February 25, 2020, 09:58:30 am
  • Time to make a bitchen man cave
Re: Kade trackball support questions
« Reply #3 on: February 10, 2015, 08:09:44 am »
Thanks.  I will give those a try tonight.
Logged
Pages: [1]
  
Go Up
« previous next »