Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: ELECTRICAL: LED powering via PSU  (Read 1146 times)

0 Members and 1 Guest are viewing this topic.

DrChek

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 231
  • Last login:August 06, 2025, 01:09:15 am
ELECTRICAL: LED powering via PSU
« on: September 05, 2012, 02:05:23 pm »
Simple question (I'm no electrician):

I have two of these LEDs that I need to wire for my coin door.

They are rated as 6.3V. Can I power them with the 5V from my computer PSU's molex connector like this?

I realize that they will be dimmer driven by 5V as opposed to 6.3V, but how bad will it be? If bad, than what do I need to do to use the 12V source from the molex connector?
Logged

DaOld Man

  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 5165
  • Last login:August 23, 2025, 09:14:19 pm
  • Wheres my coffee?
    • Skenny's Outpost
Re: ELECTRICAL: LED powering via PSU
« Reply #1 on: September 05, 2012, 02:12:08 pm »
Yeah, that should work. The link doesnt tell if the dropping resistors are built into the base, but it looks like they are.
If you needed dropping resistors, you could adjust the resistors to account for the lower voltage, thus same brightness, but I dont think 1.3 volts is going to make that big a difference in brightness anyway.
Logged

Louis Tully

  • Trade Count: (+5)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1800
  • Last login:February 13, 2015, 09:41:03 pm
Re: ELECTRICAL: LED powering via PSU
« Reply #2 on: September 05, 2012, 02:19:40 pm »
.
« Last Edit: February 12, 2015, 09:36:25 am by Louis Tully »
Logged

DrChek

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 231
  • Last login:August 06, 2025, 01:09:15 am
Re: ELECTRICAL: LED powering via PSU
« Reply #3 on: September 05, 2012, 02:20:15 pm »
Quote from: DaOld Man on September 05, 2012, 02:12:08 pm
The link doesnt tell if the dropping resistors are built into the base, but it looks like they are.

These are the bases I have and I think you're right.


I fgured it would work as I've seen similar LEDs listed as 5-6.3V on other sites.
Logged

PL1

  • Global Moderator
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9687
  • Last login:Today at 02:21:33 am
  • Designated spam hunter
Re: ELECTRICAL: LED powering via PSU
« Reply #4 on: September 05, 2012, 02:33:55 pm »
Definitely no problem with your proposed setup.

You won't have any problem with brightness running 6.3v LEDs on 5v.

I run 12v LED buttons off 5v from USB.  They don't burn your retinas, but they do light the admin buttons quite nicely.


Scott
Logged
Pages: [1]
  
Go Up
« previous next »