Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Burgertime tech question  (Read 1718 times)

0 Members and 1 Guest are viewing this topic.

srabelpawz

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 235
  • Last login:May 16, 2010, 11:07:44 am
  • I want to build my own arcade controls!
Burgertime tech question
« on: December 15, 2005, 02:01:14 am »
i sold a burgertime to a guy in LA. when the shippers(NAVL) got it to him and he turned it on the screen says mapping ok and then shows a bunch of pics of the chef. any ideas on how to get this working? did something come loose during shipping? any help would be appreciated.

Doughbroz

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 66
  • Last login:December 05, 2019, 05:23:09 pm
  • I want to build my own arcade controls!
Re: Burgertime tech question
« Reply #1 on: December 15, 2005, 08:09:00 am »
Not much could "come loose" during shipping, unless a component that sticks up above the board got torn loose, or the socketed chips need to be pressed in.  Reminds me of this, though.  Years ago, a repair shop I frequent was working on a Burgertime board.  A tech was pressing on the chips and didn't notice the soldering iron cord under the board.  When the pins punctured the insulation, it shot 110V to the board and blew out half the chips.  From that day forward, whenever one of the techs totally FUBARed anything, the others said he had "Burgertimed it". 

RayB

  • I'm not wearing pants! HA!
  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 11279
  • Last login:July 03, 2025, 11:58:07 pm
  • There's my post
    • RayB.com
Re: Burgertime tech question
« Reply #2 on: December 15, 2005, 10:14:50 am »
The usual advice (which your buying will get mad at if he's at all "tech-phobic"):

1. With power off, check that all connectors are secured, and press on all socketed chips to make sure they are firmly in the sockets.

2. Check that the TEST switch isn't on.

3. Measure voltage to the board. (This is the part they will really balk at).

4. Find out if they are using a very long electrical cord, and advise them not to do so.

..
NO MORE!!

Ken Layton

  • Guru
  • Trade Count: (+1)
  • Full Member
  • ****
  • Offline Offline
  • Posts: 7061
  • Last login:October 12, 2021, 12:25:59 am
  • Technician
Re: Burgertime tech question
« Reply #3 on: December 15, 2005, 10:15:25 am »
Could the

srabelpawz

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 235
  • Last login:May 16, 2010, 11:07:44 am
  • I want to build my own arcade controls!
Re: Burgertime tech question
« Reply #4 on: December 16, 2005, 04:58:15 am »
  thanks for the help guys. turned out a chip became unseated. Nice easy fix ;D