Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Why won't my vertical hold ???  (Read 1566 times)

0 Members and 1 Guest are viewing this topic.

jlampc

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 66
  • Last login:February 02, 2022, 07:33:58 am
  • I am not an animal !!! I am a gamer
Why won't my vertical hold ???
« on: May 02, 2004, 04:51:15 am »
Help.

I finally started assembling the monitor/ computer side of my Cabinet, and I'm having a little problem Dialing in the monitor. My system is a Virtual-on Sitdown Cabinet with a 29 inch Nanao Monitor. The monitor has been switched to 15Khz for Mame use. I'm using the Arcade Vga Card from Ultimarc with Their breakout cable patched to the monitor's signal inputs. I am pretty sure I got that right. My image is controllable from the Breakout box connected to the monitor. The breakout box is infront. It houses Vertical and Horizontal settings and Brightness and signal gain for the RGB. My Problem is this. I cannot reliably set the picture. I think its set right and a minute later its rolling slowly. The horizontal has no problem with being setup. Could the Problem be on the Breakout box??? I was just glad to see it work..Now I want it to be usable.

Thanx ???

jlampc

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 66
  • Last login:February 02, 2022, 07:33:58 am
  • I am not an animal !!! I am a gamer
Re:Why won't my vertical hold ???
« Reply #1 on: May 03, 2004, 12:20:48 am »
 ;D

This board is helpful even when I don't get a response. I went hunting through old postings and tried some things other have. It seems that even though the monitor has a both a vert and horiz sync input on the cable you should only use the H sync. I attached the h and v sync wire from the videocard and connected them to the monitor's H sync.

Bingo the screen and the controls worked and synced with no problem....

I hope to be able to show some pictures soon.


Ken Layton

  • Guru
  • Trade Count: (+1)
  • Full Member
  • ****
  • Offline Offline
  • Posts: 7061
  • Last login:October 12, 2021, 12:25:59 am
  • Technician
Re:Why won't my vertical hold ???
« Reply #2 on: May 03, 2004, 12:52:26 am »
Yes, some monitors only like sync certain ways.

Knoxximus

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 148
  • Last login:December 19, 2011, 12:22:58 am
  • Young Frozen
    • Beat-TECH Productions
Re:Why won't my vertical hold ???
« Reply #3 on: June 25, 2004, 10:50:50 pm »
I'm having the same problem only my monitor has a composite sync.  I dunno what to do..... :'(
Dumb questions deserve dumb answers.

dabone

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 898
  • Last login:May 27, 2025, 09:51:37 pm
  • Time to work...
Re:Why won't my vertical hold ???
« Reply #4 on: June 26, 2004, 09:58:23 am »
I had the same problems using g07 monitors, just follow these directions to get separate syncs and feed them to the monitor.

(Also needed if you want to use a lightgun)

http://www.ultimarc.com/vidamp.html


Later,
dabone