Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: Joystick handle hole diameter?  (Read 3258 times)

0 Members and 1 Guest are viewing this topic.

thecheat

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 85
  • Last login:October 16, 2009, 11:58:55 am
Joystick handle hole diameter?
« on: May 19, 2009, 11:50:57 pm »
Looked around a lot by searching and in the wiki, but I couldn't find my answer. What is the diameter of the hole for the stick handle on a Competition joystick? 1.125"?
Logged

thecheat

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 85
  • Last login:October 16, 2009, 11:58:55 am
Re: Joystick handle hole diameter?
« Reply #1 on: May 20, 2009, 01:09:17 pm »
Bumping this today... I'd think someone would know this off the top of their head?  ???
Logged

Wolfwood

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 18
  • Last login:May 28, 2009, 10:35:50 pm
Re: Joystick handle hole diameter?
« Reply #2 on: May 20, 2009, 09:07:52 pm »


Hmm?
Logged

thecheat

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 85
  • Last login:October 16, 2009, 11:58:55 am
Re: Joystick handle hole diameter?
« Reply #3 on: May 20, 2009, 09:13:04 pm »
Well yes, but I need the diameter of the hole where the shaft passes through the control panel. I don't want to go too big and not have the dust washer cover the hole. If I make it too small it's going to be difficult to re-bore with the hole saw and no center line.

If it's dependent on the thickness of the control panel, it's going to be 5/8".
Logged

Wolfwood

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 18
  • Last login:May 28, 2009, 10:35:50 pm
Re: Joystick handle hole diameter?
« Reply #4 on: May 20, 2009, 09:13:52 pm »


That help anything?

its about a half inch, if the joystick shaft is what your talking about.

and you could look on google, thats all I got.
« Last Edit: May 20, 2009, 09:15:23 pm by Wolfwood »
Logged

EwJ

  • Trade Count: (+6)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 366
  • Last login:October 12, 2022, 10:16:06 pm
Re: Joystick handle hole diameter?
« Reply #5 on: May 20, 2009, 09:24:47 pm »
This might have what you're looking for.
(As linked at the top of this wiki page
Logged

thecheat

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 85
  • Last login:October 16, 2009, 11:58:55 am
Re: Joystick handle hole diameter?
« Reply #6 on: May 20, 2009, 09:36:53 pm »
Quote from: EwJ on May 20, 2009, 09:24:47 pm
This might have what you're looking for.
(As linked at the top of this wiki page


YES! I was looking in the Wiki on joystick mounting and there was no entry. That is precisely what I was looking for! I thought it was 1 1/8 but wanted to be 100% sure before going too far.
Logged
Pages: [1]
  
Go Up
« previous next »