Author Topic: Re-programming the Mini-PAC - Help! [SOLVED!] (Read 1185 times)

dekar24k · « **on:** April 13, 2009, 09:34:56 am »

Hi guys!

I'm sooo close to finishing my bartop cabinet now, but I am stuck programming the Mini-PAC interface.

When I wired the buttons and joystick I didn't pay attention to the labeled connectors on the Mini-PAC and I just connected them randomly as they fit. I didn't think this was going to be a problem as I read that the Mini-Pac could be re-programmed completely.

Now, when I push "Up"/"Down" on my joystick it may output the characters 'X' and 'G' instead of 'Uparrow' and 'Downarrow'. I would therefore want to change this so when I push the joystick up, it sends the keyboard character for "Uparrow" to the computer.

Basically, how do I change what keyboard characters the different switches output to the computer? I tried using the WinIpac application from Ultimarc, but I couldn't figure out how to do it there.

All help appreciated a lot.

Neverending Project · « **Reply #1 on:** April 13, 2009, 12:34:36 pm »

Did you read through the documentation here? The Win-Ipac utility is really what you need to reprogram it.

dekar24k · « **Reply #2 on:** April 13, 2009, 12:37:43 pm »

Quote from: Neverending Project on April 13, 2009, 12:34:36 pm

Did you read through the documentation here? The Win-Ipac utility is really what you need to reprogram it.

Hmm .. I thought I'd read through it well enough. The application doesn't seem that complicated to me.

Guess I'll have to try again. Thanks!

dekar24k · « **Reply #3 on:** April 13, 2009, 12:44:55 pm »

Ergh.. Guess I was a little too quick when rushing through the WinIpac util. I get it now. I have to assign each button according to how I physically wired it in "Panel mode" first, then I can assign keyboard codes.

Ah.. I hope it's possible to reset the MiniPAC to it's default configuration, because I messed around and saved a new configuration to the ROM which screwed it up completely.

DeLuSioNal29 · « **Reply #4 on:** April 13, 2009, 01:10:03 pm »

You can reset it by going into "Programming Mode" in windows notepad.

http://www.ultimarc.com/interact.html

dekar24k · « **Reply #5 on:** April 13, 2009, 01:53:53 pm »

Quote from: DeLuSioNal29 on April 13, 2009, 01:10:03 pm

You can reset it by going into "Programming Mode" in windows notepad.

http://www.ultimarc.com/interact.html

Awesome, thanks!

I guess I'll program the Mini-PAC in programming mode as well (instead of using WinIpac). Thanks again!


Main	Restorations	Software	Audio/Jukebox/MP3	Everything Else	Buy/Sell/Trade
Project Announcements	Monitor/Video	GroovyMAME	Merit/JVL Touchscreen	Meet Up	Retail Vendors
Driving & Racing	Woodworking	Software Support Forums	Consoles	Project Arcade	Reviews
Automated Projects	Artwork	Frontend Support Forums	Pinball	Forum Discussion	Old Boards
Raspberry Pi & Dev Board	controls.dat	Linux	Miscellaneous Arcade	Wiki Discussion	Old Archives
Lightguns	Arcade1Up	Try the site in https mode		Site News


Unread posts \| New Replies \| Recent posts \| Rules \| Chatroom \| Wiki \| File Repository \| RSS \| Submit news

Author Topic: Re-programming the Mini-PAC - Help! [SOLVED!] (Read 1185 times)

dekar24k

Re-programming the Mini-PAC - Help! [SOLVED!]

Neverending Project

Re: Re-programming the Mini-PAC - Help!

dekar24k

Re: Re-programming the Mini-PAC - Help!

dekar24k

Re: Re-programming the Mini-PAC - Help!

DeLuSioNal29

Re: Re-programming the Mini-PAC - Help!

dekar24k

Re: Re-programming the Mini-PAC - Help!