Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: mdf/wood control panel  (Read 5228 times)

0 Members and 1 Guest are viewing this topic.

ablizno

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 177
  • Last login:August 15, 2011, 09:04:29 pm
  • [insert text here]
mdf/wood control panel
« on: April 13, 2008, 11:20:17 pm »
what is the best way to attach a control panel overlay from www.mamemarquees.com to a wood control panel. I will be using the adhesive polycarbinate laminate overlay.
Logged

amadama

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 201
  • Last login:September 29, 2019, 04:44:52 pm
Re: mdf/wood control panel
« Reply #1 on: April 17, 2008, 09:03:48 am »
Paint the CP with primer first then a quick sanding. You should then be ok to apply the overlay to that. I did it once without a primer coat onto the raw MDF and after about six months it started to peel off.
Good luck!
Alex
Logged

ablizno

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 177
  • Last login:August 15, 2011, 09:04:29 pm
  • [insert text here]
Re: mdf/wood control panel
« Reply #2 on: April 17, 2008, 04:37:45 pm »
Its ok im just going to use aluminum and lay a piece of plexi over top, but thank you.
Logged

Blanka

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2248
  • Last login:January 25, 2018, 03:19:28 pm
Re: mdf/wood control panel
« Reply #3 on: May 12, 2008, 11:16:09 am »
Why plexi? Try to find anodised aluminium. Nice and strong finish, no oxidation and nice looks without the need for a transparant layer on top.
Logged

Jdurg

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1127
  • Last login:October 04, 2020, 09:26:27 pm
  • A young guy feeling older than sin......
Re: mdf/wood control panel
« Reply #4 on: May 12, 2008, 12:53:44 pm »
Quote from: Blanka on May 12, 2008, 11:16:09 am
Why plexi? Try to find anodised aluminium. Nice and strong finish, no oxidation and nice looks without the need for a transparant layer on top.

Because the artwork isn't exactly durable and if you have bare artwork on top of the CP it will certainly get marred, scratched, ripped, etc. after many hours of abuse.  It's MUCH easier and cheaper to replace the plexi than it is to replace the artwork.
Logged
Donkey Kong High Scores:
1): 49,500
2): 35,600
3): 30,100
4): 29,400
5): 28,200

Blanka

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2248
  • Last login:January 25, 2018, 03:19:28 pm
Re: mdf/wood control panel
« Reply #5 on: May 12, 2008, 01:20:46 pm »
Something went wrong here. I did not get the first 2 posts. So I did not know you were about using artwork  :banghead:
Logged
Pages: [1]
  
Go Up
« previous next »