Author Topic: Pricing on coin doors, and other parts (Read 3816 times)

3dmacman · « **on:** January 11, 2008, 10:34:19 am »

I have a few coin doors in various states, some have missing pieces some have coin mechs still attached. Another item I have is an orignal NBA Jam Marquee silkscreened to plexiglass, it has a lot of scratches and the image is starting to crumble a bit, I would take $5 for that plus shipping. I will post pictures on mon. when I get back in the office. Just thought I would clear out some room.

Added stuff. June -5-08

3dmacman · « **Reply #1 on:** January 14, 2008, 09:55:42 am »

I have 37 pushbuttons for sale. 8 green, 8 blue, 10 yellow with two missing nuts;3 missing switches, and 8 white, 3 black 1 missing switch. I am looking at a dollar a piece, I also have 6 leaf switches, two red, 2 blue, 2 orange, in translucent colors. I am also asking for a dollar a piece for them. These are pulls from old cabs as well as a bunch of other stuff I will upload here this week. pm me for details on shipping. I will accept check or money order, or paypall.

3dmacman · « **Reply #2 on:** January 14, 2008, 09:57:31 am »

One original nba jam marque silkscreen on plastic taped to a sheet of plexiglass, some of the marque is starting to rub off. I want only $5 for this. I also have a neo geo blank slot marquee, it has world heroes 2 in the slot, good condition for marquee, wh2 a little faded. Buy this and I will throw in a neo geo cup instruction card. Asking $8.

3dmacman · « **Reply #3 on:** January 14, 2008, 09:59:46 am »

One over under door with coin mechs attached. I can't vouch for the condition of the mechs since these are pulled from old cabs. It is missing the coin reject buttons, the one in the picture is broke and missing the top to the button. You can buy these any where on the net for $2 to $4 a piece. I was looking in the range of $25 obo. pm offers

3dmacman · « **Reply #4 on:** January 14, 2008, 10:01:56 am »

I have two wood cp and one metal cp. I would take $10 each for the wood cp with out joysticks, and the metal cp. I would like $15 for the cp with the joysticks still in them
ignore this post.

3dmacman · « **Reply #5 on:** January 14, 2008, 10:03:13 am »

I have one wood cp and one metal cp. I would take $10 each for the wood cp joysticks, and the metal cp.

3dmacman · « **Reply #6 on:** January 14, 2008, 10:05:10 am »

~~I have two 28 pin jamma harness's for sale asking $2 for each or $3 for both.~~
SOLD

3dmacman · « **Reply #7 on:** January 14, 2008, 10:08:32 am »

I have ~~four~~ 8 = 8-way joysticks for sale, one missing switches. I would accept $5 each or two for $8. I must stress these are used and I can't vouch for the switches. All my prices do not include shipping and handling. Pm me so that I can get an estimate. I will try to go the cheapest I can on shipping. 6 are happ knock offs and two are x-gaming joys.

3dmacman · « **Reply #8 on:** January 17, 2008, 08:50:36 am »

3dmacman · « **Reply #9 on:** January 21, 2008, 04:30:04 pm »

3dmacman · « **Reply #10 on:** January 24, 2008, 09:44:42 am »

I am willing to take trades, looking for a decent trackball, spinner, a bits limited smart power strip.

3dmacman · « **Reply #11 on:** February 04, 2008, 01:47:09 pm »

3dmacman · « **Reply #12 on:** February 05, 2008, 10:50:52 am »

bumpy

shardian · « **Reply #13 on:** February 05, 2008, 11:48:55 am »

Can you verify the metal panel is from a Taito cab? I am fairly sure it is.

3dmacman · « **Reply #14 on:** February 05, 2008, 02:01:51 pm »

I am not sure these panels came from a neo geo conversion cab, I could measure them tonight and let you not tomorrow, right now I am at work.

3dmacman · « **Reply #15 on:** February 06, 2008, 12:37:19 pm »

The metal cp measures at 22 3/4w X 10 3//4 total length.

shardian · « **Reply #16 on:** February 06, 2008, 01:17:05 pm »

Quote from: 3dmacman on February 05, 2008, 02:01:51 pm

I am not sure these panels came from a neo geo conversion cab, I could measure them tonight and let you not tomorrow, right now I am at work.

Well if you saw the cabinet, did it look like this?
http://www.hyperspacearcade.com/ForSaleJungleKing.html

3dmacman · « **Reply #17 on:** February 06, 2008, 02:07:42 pm »

It was more of a generic neo geo cab, sorry.

rhuel · « **Reply #18 on:** February 11, 2008, 06:42:39 pm »

Got the buttons today!!!

Thanks!

3dmacman · « **Reply #19 on:** February 18, 2008, 04:07:50 pm »

3dmacman · « **Reply #20 on:** March 10, 2008, 11:06:14 am »

3dmacman · « **Reply #21 on:** June 05, 2008, 11:03:10 am »

Added Stuff.

SirPeale · « **Reply #22 on:** June 05, 2008, 01:10:05 pm »

How about a picture of the underside of that wooden CP. It's a Williams, I just can't figure out which one.

3dmacman · « **Reply #23 on:** June 05, 2008, 01:30:46 pm »

I can set up a pic tomorrow, right now I am at work.

3dmacman · « **Reply #24 on:** June 09, 2008, 10:25:40 am »


Main	Restorations	Software	Audio/Jukebox/MP3	Everything Else	Buy/Sell/Trade
Project Announcements	Monitor/Video	GroovyMAME	Merit/JVL Touchscreen	Meet Up	Retail Vendors
Driving & Racing	Woodworking	Software Support Forums	Consoles	Project Arcade	Reviews
Automated Projects	Artwork	Frontend Support Forums	Pinball	Forum Discussion	Old Boards
Raspberry Pi & Dev Board	controls.dat	Linux	Miscellaneous Arcade	Wiki Discussion	Old Archives
Lightguns	Arcade1Up	Try the site in https mode		Site News


Unread posts \| New Replies \| Recent posts \| Rules \| Chatroom \| Wiki \| File Repository \| RSS \| Submit news