Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Cutting Large Circles  (Read 3971 times)

0 Members and 1 Guest are viewing this topic.

Sshado

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 221
  • Last login:October 04, 2024, 06:10:57 pm
  • Sshado's Club
    • Sshado's Club
Cutting Large Circles
« on: May 05, 2003, 01:51:06 pm »
How do you cut large circles?  I need to cut a 10" circle out of 3/4" Oak Plywood and I am wondering if there is anything better than a Jigsaw for this.

Thanks,

Sshado

Veto

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 40
  • Last login:May 21, 2003, 05:35:12 pm
  • GTG 3D in Mame soon please.
Re:Cutting Large Circles
« Reply #1 on: May 05, 2003, 02:02:32 pm »
really big drill bit?

Pixelhugger

  • Trade Count: (+8)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1865
  • Last login:March 24, 2025, 05:45:13 pm
Re:Cutting Large Circles
« Reply #2 on: May 05, 2003, 02:05:26 pm »
I believe you can use a router with a circle jig. Never done it/seen it myself. :-\
Project mega thread HERE

RandyT

  • Trade Count: (+14)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 7014
  • Last login:Today at 11:25:58 am
  • Friends don't let friends hack keyboards.
    • GroovyGameGear.com
Re:Cutting Large Circles
« Reply #3 on: May 05, 2003, 02:05:55 pm »
Some routers have a circle cutting jig, or at least a way to use one.

This usually consists of a metal rod with a right angle bend on one end, and the means of clamping the other end to the base of your router.

You then drill a hole that is the same size as the rod diameter at the center of where you want your circle.  Then attach the rod to the router base so that the inside edge of the bit is at the radius of the dimension you want, if you are after the disc.  

*edit* If you are making a hole, measure to the outside edge of the bit.

Then just spin it around and cut it out.

A word of caution:  Make sure you have a waster board underneath and your rod goes into that as well.  Otherwise, as you finish your cut, there will be nothing to hold the rod and your cut will get ugly. :)

RandyT

« Last Edit: May 05, 2003, 02:29:06 pm by RandyT »

Wienerdog

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 569
  • Last login:December 08, 2020, 06:28:51 am
  • If it's worth doing, it's worth overdoing
Re:Cutting Large Circles
« Reply #4 on: May 05, 2003, 02:22:33 pm »
You can also build a router jig out of pegboard or hardboard.  

Cut a scrap piece of pegboard (or any wood for that matter, pegboard just has some holes already.  If you use hardboard, you can drill your own hole) into a 5" x 3' piece.  In your case, you would only need a piece about 12" long, since the center of your circle will be 5" from the router bit.

Remove the base plate of your router, and screw the wood to the router using countersunk screws.  You will have to cut an opening for your router bit to fit through.  Now just measure the desired distance from the router bit and drill a hole at the centerpoint of your circle.  If your really wanted a 10" wooden disc, then measure 5" from the inside of the router bit, if you wanted a 10" hole, then measure from the outside of the router bit :).

Opps, I should mention that this process is easier with a plunge router.  I've done it with a fixed base router, but it is tricky to start the cut...
This opinion was created from 100% post consumed information.

thedemo

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 25
  • Last login:May 21, 2003, 06:30:04 pm
  • I want to rule the world
Re:Cutting Large Circles
« Reply #5 on: May 05, 2003, 05:44:30 pm »
you could invest in a Rotozip kit for about $90. The kit comes with the Rotozip itself, a grinding attachment for metal and wood and a handy attachment for making circles up too I think 20 inches across.

shmokes

  • Just think of all the suffering in this world that could have been avoided had I just been a little better informed. :)
  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 10397
  • Last login:September 24, 2016, 06:50:42 pm
  • Don't tread on me.
    • Jake Moses
Re:Cutting Large Circles
« Reply #6 on: May 05, 2003, 06:27:15 pm »
Here's what I do.  Get a 5" length of rope and nail one end of it into the center of the the soon to be circle.  Nail the other end into the side of your circular saw and let her rip.



Just kidding.
Check out my website for in-depth reviews of children's books, games, and educational apps for the iPad:

Best Kid iPad Apps

OSCAR

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1770
  • Last login:September 06, 2018, 11:31:53 pm
  • I think Bigfoot is blurry, that's the problem...
    • Oscar Controls
Re:Cutting Large Circles
« Reply #7 on: May 05, 2003, 06:32:37 pm »
I have both of these and they work great.

Large circle jig

Small circle jig

Wienerdog

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 569
  • Last login:December 08, 2020, 06:28:51 am
  • If it's worth doing, it's worth overdoing
Re:Cutting Large Circles
« Reply #8 on: May 06, 2003, 01:45:13 am »
Here's what I do.  Get a 5" length of rope and nail one end of it into the center of the the soon to be circle.  Nail the other end into the side of your circular saw and let her rip.

Just kidding.
You have to start that procedure off with a six pack of beer to steady your hand.

I am also just kidding, but all non-powertool related procedure should start off with a six pack.  

The first link from Oscar is what I was describing.  You can build a quick jig, but it is obviously better to purchase a good quality one like that.  Basically the polyethylene material will be much better than fiber board at 1/4", but that doesn't mean you can't whip one out with fiber board if you need a quick jig.  Just make sure it is safe.
This opinion was created from 100% post consumed information.

hyiu

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1481
  • Last login:August 29, 2014, 05:36:15 am
  • too many games... too little time....
    • www
Re:Cutting Large Circles
« Reply #9 on: May 06, 2003, 05:01:12 pm »
that is a very nice tool !!! oscar...

I think the small one is worth the $$.....
soon.... I'll need to cut a 3" hole for the trackball....

thanks....

its nice to learn something new here everyday....

Another Brilliant mind ruined by education....  :p