Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: 9 Person Poker Table - Built in cameras like the pros.  (Read 15054 times)

0 Members and 6 Guests are viewing this topic.

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
9 Person Poker Table - Built in cameras like the pros.
« on: January 05, 2007, 12:44:02 am »
I am building my second poker table.  I built an octogan style table for my house last February.  I am now in the process of building a Horse Track style table for a buddy.  I don't know if I'm going to be adding lighting or not, but I am looking forward to it.  I am excited about adding the dealer area.  Nothing fancy here, just a good ol' poker table.

The first thing I did was cut the bottom part, or the playing field, first.  I used a router template to cut the rounded edges.  I think one could use a 1/4" piece of plexi to make their own template.  Here is the bottom cut and the router screwed into the template.  The playing area is made of a nice 3/4" piece of birch plywood.







I next moved onto making the top.  The toughest challenge was making the dealers area.  I always wanted to do this, but I never had a clue how to do it.  So.........I took a few extra pieces of scrap wood and extended out from the table.  This gave me a nice square center point to cut the area out.  I first marked the curve with a yardstick that had a couple holes drilled in it.  That was very helpful to ensure the proper measurements.  Here is the top in all it's glory.  I made it out of 5/8" mdf.













This process made the most sawdust I've ever seen.  This pile was every bit of 4-6"'s tall.



Here is the top sitting on the bottom.  I still have a long ways to go, but the hardest part for me is done.(Getting started  ;) )





Here is the width of the table including armrest.  The table is 84"'s long.



Important note:  I used a round over bit to keep the edges of the wood soft.  I used a slight round over on three sides, and on the outside bottom, I did a 3/8" roundover so the future rail covering won't be rubbing against a hard surface.
« Last Edit: March 25, 2007, 01:16:30 am by mccoy178 »

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
For Costs Purposes.

Donkey_Kong

  • heh. I dont know what it stands for but I'm immature and thats hilarious.
  • Trade Count: (+14)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1693
  • Last login:October 20, 2019, 12:39:54 am
    • CNC Machines
Dude, I came across your photo album one day of your tables and other furniture. I don't remember where it was located. Do you have a link for it you could share? I remember it being pretty flashy...
Carved Signs, Custom Gameroom Signs, and Arcade Game Decor and now CNC MACHINES by Melissa Jones

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Some of the things I've done can be seen at

www.ohiostate.photosite.com

Donkey_Kong

  • heh. I dont know what it stands for but I'm immature and thats hilarious.
  • Trade Count: (+14)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1693
  • Last login:October 20, 2019, 12:39:54 am
    • CNC Machines
Ben that photo album is amazing! Why don't you link to it in your siggy?
Carved Signs, Custom Gameroom Signs, and Arcade Game Decor and now CNC MACHINES by Melissa Jones

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Ah, I don't know.  Most of them are not very well documented projects, so I just didn't think people would want to see them.  I wish I would've documented the bookcase/tv area better.  I loved that project very much.  I also really liked doing the lighting soffit in the pool table room.  It was one of my first "just see what happens" kind of project and I feel it is one of the coolest parts of the house.  Thanks for the compliments! :cheers:

Donkey_Kong

  • heh. I dont know what it stands for but I'm immature and thats hilarious.
  • Trade Count: (+14)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1693
  • Last login:October 20, 2019, 12:39:54 am
    • CNC Machines
Damn I just seen the Gauntlet again, I seen that one before it is phenom...& The Bo-Sox  :o

Didn't you make all those cabs for someone else?

oh yea the poker table is aight too! heh. sorry.
« Last Edit: January 05, 2007, 01:48:15 am by Donkey_Kong »
Carved Signs, Custom Gameroom Signs, and Arcade Game Decor and now CNC MACHINES by Melissa Jones

DrewKaree

  • - AHOTW - Pompous revolving door windbag *YOINKER*
  • Wiki Master
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9740
  • Last login:May 15, 2021, 05:31:18 pm
  • HAH! Nice one!
    • A lifelong project
You’re always in control of your behavior. Sometimes you just control yourself
in ways that you later wish you hadn’t

DrewKaree

  • - AHOTW - Pompous revolving door windbag *YOINKER*
  • Wiki Master
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9740
  • Last login:May 15, 2021, 05:31:18 pm
  • HAH! Nice one!
    • A lifelong project
How wide is that cutout for the dealer's area, and will you be making the rail follow that shape as well or leaving an "opening"?

What are you going to be doing for the legs also?  Seems like the standard banquet table legs would cheapen the look and pedestals would take up too much room.
You’re always in control of your behavior. Sometimes you just control yourself
in ways that you later wish you hadn’t

Rich

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 15
  • Last login:January 05, 2008, 01:15:13 pm
Very cool! I like how you cut the dealers spot. I built one last year, but ti looks like yours will turned out alot nicer.

DrewKaree

  • - AHOTW - Pompous revolving door windbag *YOINKER*
  • Wiki Master
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9740
  • Last login:May 15, 2021, 05:31:18 pm
  • HAH! Nice one!
    • A lifelong project
Very cool! I like how you cut the dealers spot. I built one last year, but ti looks like yours will turned out alot nicer.

There's a few questions about his skill with his hands, so I wouldn't be so sure of that just yet.  Many PCB's with effed up solder points would second this notion as well ;)
You’re always in control of your behavior. Sometimes you just control yourself
in ways that you later wish you hadn’t

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Very cool! I like how you cut the dealers spot. I built one last year, but ti looks like yours will turned out alot nicer.

There's a few questions about his skill with his hands, so I wouldn't be so sure of that just yet.  Many PCB's with effed up solder points would second this notion as well ;)

Electronics, not so much.  Woodworking, a little better. :applaud:

theCoder

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1035
  • Last login:September 20, 2010, 10:48:47 pm
  • I'll clean up my mess, Honey, when I'm done...
What are your plans for the playing surface?  Perhaps a stiff but plyable cork surface covered in green felt?

That's a cool router jig.  Standard stuff or hard to find?

What, no electronics?  Come on...

Rich

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 15
  • Last login:January 05, 2008, 01:15:13 pm
What are your plans for the playing surface?  Perhaps a stiff but plyable cork surface covered in green felt?

Since I've built mine at least one person spills something on it at every game.  :hissy: I think closed  cell foam covered with speed cloth is what I'd use next time.

arcadefever

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 795
  • Last login:June 03, 2009, 09:45:05 pm
  • Miami Beach Florida
Some of the things I've done can be seen at

www.ohiostate.photosite.com


 :dizzy:



this is what i think about it ------> :notworthy:

GadgetGeek

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 414
  • Last login:July 09, 2024, 09:32:57 am
  • whatever
Is it going to have red felt for the playing surface?  With a big O in front of each player's station, or centered on the table, or ...

Donkey_Kong

  • heh. I dont know what it stands for but I'm immature and thats hilarious.
  • Trade Count: (+14)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1693
  • Last login:October 20, 2019, 12:39:54 am
    • CNC Machines
Is it going to have red felt for the playing surface?  With a big O in front of each player's station, or centered on the table, or ...

Something like this would be a great idea for sure!! Here are a couple of custom felt links mccoy...


http://www.poolfelt.com/custom_designs_pool_table_felt.html

http://www.poker-wear.com/poker_felt_table_cloth.htm

 :cheers:
Carved Signs, Custom Gameroom Signs, and Arcade Game Decor and now CNC MACHINES by Melissa Jones

Kaytrim

  • I'm too nice a guy
  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2095
  • Last login:September 22, 2015, 04:11:30 pm
That second link even has the Ohio State logo on felt.  The price is astronomical though for a 4' x 8' piece.
$467.50 + $19.95 shipping to the 48 states.   :hissy: OUCH!!! :angry:

NIVO

  • Global Moderator
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 1256
  • Last login:August 08, 2022, 12:32:13 pm
  • danny_galaga is my mail man.
    • N.A.M.E. - arcade cabinet project
Drew and I have concluded that this wont be complete without a Lemon logo Ben, get crackin!   :hissy:

DrewKaree

  • - AHOTW - Pompous revolving door windbag *YOINKER*
  • Wiki Master
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9740
  • Last login:May 15, 2021, 05:31:18 pm
  • HAH! Nice one!
    • A lifelong project
Drew and I have concluded that this wont be complete without a Lemon logo Ben, get crackin!   :hissy:

I thought that's what that big O thing was that he's fond of :dunno
You’re always in control of your behavior. Sometimes you just control yourself
in ways that you later wish you hadn’t

NIVO

  • Global Moderator
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 1256
  • Last login:August 08, 2022, 12:32:13 pm
  • danny_galaga is my mail man.
    • N.A.M.E. - arcade cabinet project
hehehe Drew +FU....................................DOH!  :banghead:

(+_+)

  • Let me splain.
  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 652
  • Last login:July 27, 2012, 09:00:32 pm
  • For I am ]{eyser Soze
Do you have space between the table and the rim to tuck in the felt between them. That would give it a clean finish and avoid a potential bad cut.
This plan is so perfect, it's retarded. -- Peter Family Guy

Glaine

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 563
  • Last login:April 24, 2013, 12:09:17 pm
I like the indented playing surface. I would love to make a craps table 1 day...

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Long time no post, but it's been a busy quarter at school.  I've finally got back to the table and started the plexi glass inlays for the camera system.  Oh, did I forget to mention that?  This table is for my buddy.  He has already purchased a camera system for it and now it's on me to build the table.  I am building one for myself, and I will have a separate thread for that one.  Anyways, here is the update with pics.

First thing I did was mark where the cameras were to go.  Then I used the old plexi from my first cabinet I built to make the inlay jig.  Here is the setup for that, the bit I used, (1/2" spiral bit), and the finished product.  On a side note, I'm looking forward to making actual design inlays in future projects.  It's really simple.
« Last Edit: March 25, 2007, 01:07:02 am by mccoy178 »

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Next, I made the inlay on the table for the first camera area.  I used an 1/8" inlay kit for the lip the plexi is to sit on, and a 1/2" inlay kit for the complete cutout.

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Here is more pics with the inlay jig on the freshly cut hole.

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
I then attempted to use the inlay kit to cut the 1/2" plexi, and let's just say, it would take me ten years doing it that way.  I used my table saw to cut the plexi and it looks great.  I left the plexi sticking up a little more than an 1/8" out of the table so once the felt and 1/4" foam are installed, the plexi will be very close to the height of the playing felt.  Here are pics of the final product from a couple different angles and at the end I have a demonstration of how well the cards fit on the plexi.  Now I only have to do it 8 more times.  Yay me. :dizzy:

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
More.

theCoder

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1035
  • Last login:September 20, 2010, 10:48:47 pm
  • I'll clean up my mess, Honey, when I'm done...
What, no electronics?  Come on...
I knew you would find a way.

The windows will complicate how you handle the felt.  I guess you could use the glass to trap the felt in a pocket.

And the camera system?  Do tell.

DrewKaree

  • - AHOTW - Pompous revolving door windbag *YOINKER*
  • Wiki Master
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9740
  • Last login:May 15, 2021, 05:31:18 pm
  • HAH! Nice one!
    • A lifelong project
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #29 on: March 25, 2007, 03:10:33 pm »
Why IS your buddy wanting a camera system?  Seems like a useless gimmick unless a game is being televised, and/or a way for two cheaters to hose your game and split the pot afterwards - at least for a HOME game :dunno
You’re always in control of your behavior. Sometimes you just control yourself
in ways that you later wish you hadn’t

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #30 on: March 25, 2007, 05:15:20 pm »
Why IS your buddy wanting a camera system?  Seems like a useless gimmick unless a game is being televised, and/or a way for two cheaters to hose your game and split the pot afterwards - at least for a HOME game :dunno
Hey Chad, wrong board, EE is elsewhere.  We play a lot of big poker games.  The way his poker room is set up, he has another room with a big screen where second games get started.  And, we've both won enough money playing (after taxes of course), to pay for this stuff, so there! 

What, no electronics?  Come on...
I knew you would find a way.

The windows will complicate how you handle the felt.  I guess you could use the glass to trap the felt in a pocket.

And the camera system?  Do tell.

I will give more details in the future.  I have so many projects going on, I can't keep my head straight.  I do plan on using the plexi against the felt to help lock it into place.  I left just a tiny bit of space to create a nice sandwich.

blueznl

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 290
  • Last login:June 16, 2019, 04:50:02 pm
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #31 on: March 25, 2007, 05:50:42 pm »
Besides... if he likes it, let him have it!  :dunno

DrewKaree

  • - AHOTW - Pompous revolving door windbag *YOINKER*
  • Wiki Master
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9740
  • Last login:May 15, 2021, 05:31:18 pm
  • HAH! Nice one!
    • A lifelong project
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #32 on: March 25, 2007, 06:19:01 pm »
Besides... if he likes it, let him have it!  :dunno

Yeah, what he said...because you clearly saw me say "don't do it" ::)

Hey McCoy, I musta missed the part where the possibility of someone cheating is a good thing in your games, and the rules where bringing up something like that was a Chadism.  Please print your rules clearer, because I thought asking a question was within bounds, and giving reason for asking such a question would be a McCoyism.

Maybe we should vote on it :recoil
You’re always in control of your behavior. Sometimes you just control yourself
in ways that you later wish you hadn’t

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #33 on: March 25, 2007, 07:39:44 pm »
Why IS your buddy wanting a camera system?  Seems like a useless gimmick unless a game is being televised, and/or a way for two cheaters to hose your game and split the pot afterwards - at least for a HOME game :dunno

I'm sorry, after further review, I don't know how I took this reply in such a negative light.  After spending more than an hour getting that first hole cut and looking forward to eight more, that's just what I was looking forward to reading.  So, after rereading your post, let me rephrase my answer:

We have a faithful group of about 30 guys in our town that love to play poker.  There are five of us that started a league and my buddy is one of those.  Since we five tend to hold the "big" tourneys and events, he thought the camera system would be a cool addition to draw a bigger crowd.  (Bigger crowd as in maybe 40 guys).  Every year during the Super Bowl, he has a really big game that people talk about for weeks in advance.  There is always secondary tourneys that start and everyone usually sticks around to watch the big game.  He has a 65" big screen in a room opposite of the main poker room that he plans on showing the hands of the final table.  As far as cheating is concerned, we aren't playing for substantial stakes and there is only a couple of us that I trully believe could pull it off anyways.  It was not made for that intention at all and we just love to play poker.  Again, we did pretty good as an entire whole last year and we like to pimp our rides when it comes to arcade machines, entertainment areas, and poker tables.  I hope this was a satisfactory answer.  If you have further questions wondering about our intentions, please ask, and I will happily bow down and answer them without the slightest hint of humor even if I feel the questions sucked after putting so much time and effort into it. :)

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #34 on: March 25, 2007, 07:44:36 pm »
Oh, and it's a Chadism because you only noted the negative aspects of the idea and left it at that.  It turned into a MrC P&R discussion once you decided to settle this discussion through a lengthy reply that tends to lend the opinion that my reply bothered you by using a gimmicky reply yourself.  So, can we get back to the Project Announcement board? :dunno

Donkey_Kong

  • heh. I dont know what it stands for but I'm immature and thats hilarious.
  • Trade Count: (+14)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1693
  • Last login:October 20, 2019, 12:39:54 am
    • CNC Machines
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #35 on: March 25, 2007, 09:56:28 pm »
Why IS your buddy wanting a camera system?  Seems like a useless gimmick unless a game is being televised, and/or a way for two cheaters to hose your game and split the pot afterwards - at least for a HOME game :dunno

I'm sorry, after further review, I don't know how I took this reply in such a negative light.  After spending more than an hour getting that first hole cut and looking forward to eight more, that's just what I was looking forward to reading.  So, after rereading your post, let me rephrase my answer:

We have a faithful group of about 30 guys in our town that love to play poker.  There are five of us that started a league and my buddy is one of those.  Since we five tend to hold the "big" tourneys and events, he thought the camera system would be a cool addition to draw a bigger crowd.  (Bigger crowd as in maybe 40 guys).  Every year during the Super Bowl, he has a really big game that people talk about for weeks in advance.  There is always secondary tourneys that start and everyone usually sticks around to watch the big game.  He has a 65" big screen in a room opposite of the main poker room that he plans on showing the hands of the final table.  As far as cheating is concerned, we aren't playing for substantial stakes and there is only a couple of us that I trully believe could pull it off anyways.  It was not made for that intention at all and we just love to play poker.  Again, we did pretty good as an entire whole last year and we like to pimp our rides when it comes to arcade machines, entertainment areas, and poker tables.  I hope this was a satisfactory answer.  If you have further questions wondering about our intentions, please ask, and I will happily bow down and answer them without the slightest hint of humor even if I feel the questions sucked after putting so much time and effort into it. :)

Hey GUYS!! I got a frickin SNAKE man!!





PS: Mccoy...your poker tables rule!! -FU for DK
Carved Signs, Custom Gameroom Signs, and Arcade Game Decor and now CNC MACHINES by Melissa Jones

mccoy178

  • It's hard to work with a straight jacket on
  • Trade Count: (+9)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3127
  • Last login:September 03, 2021, 10:23:42 am
  • Go Bucks!
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #36 on: March 26, 2007, 12:05:30 am »
I was able to finish the inlays tonight.  It took about three hours to finish.  On the last one, I took pictures of the jig and the stages of routing to clean it up.  I also set the armrest on the table to vision what it's going to look like.  I think it will be pretty cool.














Morphiuzzz

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 1
  • Last login:March 26, 2021, 02:56:18 am
  • I want to build my own arcade controls!
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #37 on: March 26, 2021, 02:20:22 am »
This is amazing.  Did you ever finish this table??  I would love to see a finished version.  Please text me photos at (630) 696-8456 if you have them.  Thanks!

thomas_surles

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2118
  • Last login:September 13, 2024, 06:34:49 pm
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #38 on: March 26, 2021, 07:41:00 pm »
This is amazing.  Did you ever finish this table??  I would love to see a finished version.  Please text me photos at (630) 696-8456 if you have them.  Thanks!
I'm drunk calling from now on

yotsuya

  • Trade Count: (+21)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 19958
  • Last login:September 14, 2024, 08:17:47 pm
  • 2014 UCA Winner, 2014, 2015, 2016 ZapCon Winner
    • forum.arcadecontrols.com/index.php/topic,137636.msg1420628.html
Re: 9 Person Poker Table - Built in cameras like the pros.
« Reply #39 on: March 27, 2021, 02:13:06 pm »



Sent from my iPhone using Tapatalk
***Build what you dig, bro. Build what you dig.***