Author Topic: need happ P360 measure. (Read 2177 times)

bossyman15 · « **on:** March 25, 2006, 01:08:48 am »

right now my CP is cut out for ulrimarc t-mag and one of hole (center of hole) is just under 3 inches from one of holes for trackball mount.

see i might buy p360 sometime in the future when i have money

so that's why i need measure of p360 so if i want to change joystick in the future it will fit in tight space.

anybody?

KDOG · « **Reply #1 on:** March 25, 2006, 01:18:29 am »

I think all of the happs bases are the same. So if you can find either a super or comp measurement you should be strait.

RichyRich · « **Reply #2 on:** March 25, 2006, 07:55:22 am »

It will not fit,but you could always drill the hole pattern in the base of the 360.

bossyman15 · « **Reply #3 on:** March 25, 2006, 08:39:42 am »

well you could just give me the measure of the base and i will cut it out on paper and see if it will fit.

Quarters · « **Reply #4 on:** March 25, 2006, 08:47:40 am »

The p360 base is a standard 3'' by 3.5'' same as most joysticks. There are some exceptions.

The pattern from the happ ultimate will work fine.LINK

bossyman15 · « **Reply #5 on:** March 25, 2006, 10:09:42 am »

Exceptions? What exceptions?

And which side is 3" and 3.5"? Top/bottom or left/right side?

RichyRich · « **Reply #6 on:** March 25, 2006, 10:57:51 am »

I got both sticks and they do not match,can't be arsed to measure.

bossyman15 · « **Reply #7 on:** March 25, 2006, 12:13:44 pm »

Everybody everybody everybody.... Anybody who have P360 would please help a fellow out and measure the top square base. Or any site with tempte of P360 would be helpful.

rwhip41 · « **Reply #8 on:** March 25, 2006, 01:00:46 pm »

The 360 I have measures 3.482" left to right and 2.985" up to down as it would sit in a control panel. In case it's relevant, it measures 0.305" thick.

Fozzy The Bear · « **Reply #9 on:** March 25, 2006, 01:01:32 pm »

Quote from: bossyman15 on March 25, 2006, 12:13:44 pm

Everybody everybody everybody.... Anybody who have P360 would please help a fellow out and measure the top square base. Or any site with tempte of P360 would be helpful.

This is the P360 mounting, actual size.... Print it at 72dpi... and yes it is the right way round.

Best Regards,
Julian (Fozzy The Bear)

Flinkly · « **Reply #10 on:** March 25, 2006, 01:29:05 pm »

you could mount a 360 the wrong way and just change the contacts. see, it has contacts labeled up down left and right, but if you oriented the joystick the skinny way, you could just change left and right to up and down and vice versa.

RichyRich · « **Reply #11 on:** March 25, 2006, 02:41:51 pm »

Hey fozzy, are you sure thats the right way round? if I pushed up on mine with your template it would activate right or left.Mines 90 degrees rotated???

EDIT:you could be right fozzy,I think I remember undoing the four screws and turning it now ,so its easily altered.

bossyman if you follow the link that Quarters kindly posted, the outside holes are the exact size of the 360.There are no inside holes on the 360 like other Happ bases which is why it wont fit your pattern but like I said earlier you could drill your own.

Fozzy The Bear · « **Reply #12 on:** March 25, 2006, 02:59:19 pm »

Quote from: RichyRich on March 25, 2006, 02:41:51 pm

Hey fozzy, are you sure thats the right way round? if I pushed up on mine with your template it would activate right or left.Mines 90 degrees rotated???

Interesting.... Mine in my first panel is that way round.... rwhip41 appears to have it that way round as well according to his measurements.

Best Regards,
Julian (Fozzy The Bear)

RichyRich · « **Reply #13 on:** March 25, 2006, 03:15:19 pm »

Just checked and you can rotate it so you can have it either way but it is sent like your template.

bossyman15 · « **Reply #14 on:** March 25, 2006, 05:17:59 pm »

Everybody thank you for your repies. Those info are very helpful. I will check it out when I get home from work within the hour.

bossyman15 · « **Reply #15 on:** March 27, 2006, 03:37:28 pm »

Quote from: Fozzy The Bear on March 25, 2006, 01:01:32 pm

This is the P360 mounting, actual size.... Print it at 72dpi... and yes it is the right way round.

Best Regards,
Julian (Fozzy The Bear)

how do i print it at 72dpi?... what program do i use?

bossyman15 · « **Reply #16 on:** March 27, 2006, 03:55:27 pm »

oh never mind i got it
i loaded it up in visio and got it.

it printed out as 3 9/16" x 3 1/8"

is that right?

rwhip41 · « **Reply #17 on:** March 27, 2006, 11:28:19 pm »

I already supplied the measurements above from my 360. I used my micrometers, which are accurate to 0.001". Based on those measurements and those supplied by others, I would rely on 3.5" x 3".

Havok · « **Reply #18 on:** March 28, 2006, 08:43:20 am »

Quote from: Fozzy The Bear on March 25, 2006, 02:59:19 pm

Quote from: RichyRich on March 25, 2006, 02:41:51 pm
Hey fozzy, are you sure thats the right way round? if I pushed up on mine with your template it would activate right or left.Mines 90 degrees rotated???

Interesting.... Mine in my first panel is that way round.... rwhip41 appears to have it that way round as well according to his measurements.

Best Regards,
Julian (Fozzy The Bear)

If you want the contacts to be correct (left is left, etc.) then you have to mount it "sideways" with the contacts to the right. You could mount it any way you want, just be aware you have to switch your connections to compensate...

RichyRich · « **Reply #19 on:** March 28, 2006, 09:15:41 am »

not true....if you undo the four screws on the base you can turn the sensors 90 degress to match up.It's really easy to do.

Havok · « **Reply #20 on:** March 28, 2006, 09:44:41 am »

Quote from: RichyRich on March 28, 2006, 09:15:41 am

not true....if you undo the four screws on the base you can turn the sensors 90 degress to match up.It's really easy to do.

It's true until you do that...

Fozzy The Bear · « **Reply #21 on:** March 28, 2006, 10:04:32 am »

Quote from: bossyman15 on March 27, 2006, 03:37:28 pm

how do i print it at 72dpi?... what program do i use?

When you print it just tell your printer to print at 72dpi.....

In you printers properties screen.

Either that or load it up in something like photoshop if you have it and resize it to 300dpi while keeping the actual dimensions.

Best Regards,
Julian (Fozzy The Bear)

RichyRich · « **Reply #22 on:** March 28, 2006, 11:18:04 am »

Quote from: Havok on March 28, 2006, 09:44:41 am

Quote from: RichyRich on March 28, 2006, 09:15:41 am
not true....if you undo the four screws on the base you can turn the sensors 90 degress to match up.It's really easy to do.

It's true until you do that...

lol


Main	Restorations	Software	Audio/Jukebox/MP3	Everything Else	Buy/Sell/Trade
Project Announcements	Monitor/Video	GroovyMAME	Merit/JVL Touchscreen	Meet Up	Retail Vendors
Driving & Racing	Woodworking	Software Support Forums	Consoles	Project Arcade	Reviews
Automated Projects	Artwork	Frontend Support Forums	Pinball	Forum Discussion	Old Boards
Raspberry Pi & Dev Board	controls.dat	Linux	Miscellaneous Arcade	Wiki Discussion	Old Archives
Lightguns	Arcade1Up	Try the site in https mode		Site News


Unread posts \| New Replies \| Recent posts \| Rules \| Chatroom \| Wiki \| File Repository \| RSS \| Submit news