Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: New grommet for old pacman sticks HELP!!  (Read 1356 times)

0 Members and 1 Guest are viewing this topic.

juggle50

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 323
  • Last login:July 18, 2024, 07:25:48 am
  • Your either on the bus or off the bus
New grommet for old pacman sticks HELP!!
« on: February 27, 2006, 10:06:03 pm »
I got a replacement grommet from ponyboy but I can't figure out how to replace it.  It has a bigger diameter hole than the original grommet.  Any suggestions.

Logged

markrvp

  • ARGHHHHHHHHHHHHH!!!!!!!!!! True Genius!
  • Wiki Contributor
  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3353
  • Last login:September 14, 2020, 10:19:57 am
  • NFL Expert
Re: New grommet for old pacman sticks HELP!!
« Reply #1 on: February 27, 2006, 10:43:31 pm »
Quote from: juggle50 on February 27, 2006, 10:06:03 pm
I got a replacement grommet from ponyboy but I can't figure out how to replace it.  It has a bigger diameter hole than the original grommet.  Any suggestions.


The grommet Ponyboy has listed in his thread IS NOT for an original Pacman joystick.  Those grommets are for WICO leafswitch joysticks.

The one for the original Pacman joysticks is available in this auction:

AUCTION LINK

Even though it says MsPacman, it is the same joystick for Pacman.  I know because I bought one and it works perfectly in my original Pacman joystick.
Logged

RandyT

  • Trade Count: (+14)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 7024
  • Last login:September 13, 2025, 08:12:16 am
  • Friends don't let friends hack keyboards.
    • GroovyGameGear.com
Re: New grommet for old pacman sticks HELP!!
« Reply #2 on: February 27, 2006, 11:39:34 pm »

Ok, who has a set of micrometers and can measure that shaft.  Is it bigger than .257" ?

Thanks,
RandyT
Logged

juggle50

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 323
  • Last login:July 18, 2024, 07:25:48 am
  • Your either on the bus or off the bus
Re: New grommet for old pacman sticks HELP!!
« Reply #3 on: February 28, 2006, 02:25:28 am »
Sorry Randy,

No micrometer on me however here is a link to a picture that has the diameter of the original grommet.

http://www.pac-man.com/images/gromlogo.jpg


Thank you for the info Markrvp, unfortunately I found out it didn't fit the hard way.  Took a couple of hours to take my cp and joystick apart only to find out I had the wrong grommet.  My bad, I wasn't looking at the fine print when I bought it.
Logged
Pages: [1]
  
Go Up
« previous next »