Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: removing brand stamp from lumber for staining  (Read 858 times)

0 Members and 1 Guest are viewing this topic.

WonderMellon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 65
  • Last login:February 10, 2019, 12:41:23 am
  • I want my own arcade controls!
removing brand stamp from lumber for staining
« on: January 11, 2005, 10:00:54 am »
For those of you who have done stained cabinets.  I have purchased a few wood pieces from Home Depot.  The big plywood sheets do not have any marks on them, but the smaller pieces are stamped with the lumber company and type of wood.  It looks like some kind of paint or ink stamp.  How do you remove this for staining?
I was told that rubbing alchohol and  #0 steel wool might take it off, but that does not remove it all.  Any suggestions?
Logged

IMMark

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 94
  • Last login:August 05, 2016, 07:30:02 pm
  • I want to build my own arcade controls!
Re: removing brand stamp from lumber for staining
« Reply #1 on: January 11, 2005, 10:09:50 am »
sanding it out will work...and will leave you with a nice smooth surface.  If you sand it, do the whole board, not just the spot...or it will take the stain differently.
Logged

Shape D.

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1602
  • Last login:July 05, 2012, 06:17:57 pm
  • >Look at me, I'm a Newbie<
Re: removing brand stamp from lumber for staining
« Reply #2 on: January 11, 2005, 11:15:34 am »
Don't they usually only stamp one side of the board? If thats the case you could use the other side.
Logged
Hey Baby, Have you ever met a Newbie with 38 pages of previous posts before? Do you Want to?

DrewKaree

  • - AHOTW - Pompous revolving door windbag *YOINKER*
  • Wiki Master
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9740
  • Last login:May 15, 2021, 05:31:18 pm
  • HAH! Nice one!
    • A lifelong project
Re: removing brand stamp from lumber for staining
« Reply #3 on: January 11, 2005, 08:42:52 pm »
Also, if you're using a water based stain / poly, that steel wool may shed fibers in use and potentially rust over time, ruining your finish later on down the road.

Sand the whole board down through progressively finer grits and you'll be good.
Logged
You’re always in control of your behavior. Sometimes you just control yourself
in ways that you later wish you hadn’t

WonderMellon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 65
  • Last login:February 10, 2019, 12:41:23 am
  • I want my own arcade controls!
Re: removing brand stamp from lumber for staining
« Reply #4 on: January 11, 2005, 09:14:51 pm »
Thanks

I was going to bring out the sander anyway, but it looks like it will solve the stamp problem as well.
Logged
Pages: [1]
  
Go Up
« previous next »