Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: Tekken 2 kick harness  (Read 1364 times)

0 Members and 1 Guest are viewing this topic.

Raven..

  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1082
  • Last login:June 29, 2021, 12:51:50 am
Tekken 2 kick harness
« on: December 21, 2004, 12:04:01 am »
Has anyone tried building their own Tekken kick harness?  Sure I can buy one, but this IS BYOAC after all....  It looks like an old 5 1/4 floppy drive edge connector on a ribbon cable should work (with a slight mod).
Logged

Grauwulf

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 341
  • Last login:July 27, 2009, 03:42:44 pm
  • Button Masher
Re: Tekken 2 kick harness
« Reply #1 on: December 21, 2004, 06:06:49 am »
The kick harness for Tekken 2 is a 48 pin connector(according to my manual). The one for a floppy is only going to be 34 I believe.
Logged
www.wolfelectronics.ca

Cap Kits for Canadians!

dabone

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 898
  • Last login:July 15, 2025, 08:32:17 pm
  • Time to work...
Re: Tekken 2 kick harness
« Reply #2 on: December 21, 2004, 08:55:07 am »
I saw a page somewhere when someone just rerouted to kick harness wires over to unused pins on the jamma connector.



Just a few jumper wires and done.

Later,
dabone


Logged

Raven..

  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1082
  • Last login:June 29, 2021, 12:51:50 am
Re: Tekken 2 kick harness
« Reply #3 on: December 22, 2004, 11:40:40 pm »
Quote from: Grauwulf on December 21, 2004, 06:06:49 am
The kick harness for Tekken 2 is a 48 pin connector(according to my manual). The one for a floppy is only going to be 34 I believe.

Right.  I cut two of them to make the full length.  I haven't wired it up to the buttons yet though.....to cold in the garage to mess with right now!
Logged

wboy

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 176
  • Last login:November 03, 2005, 05:09:19 pm
  • I'm a llama!
Re: Tekken 2 kick harness
« Reply #4 on: December 23, 2004, 07:42:31 am »
you can find them brand new on ebay for around $15US or so from time to time.
Logged

Grauwulf

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 341
  • Last login:July 27, 2009, 03:42:44 pm
  • Button Masher
Re: Tekken 2 kick harness
« Reply #5 on: December 23, 2004, 06:07:47 pm »
I'm just doing the jumper wire method on mine.
Logged
www.wolfelectronics.ca

Cap Kits for Canadians!
Pages: [1]
  
Go Up
« previous next »