Author Topic: Will do machine work for.... (Read 2144 times)

GameDork · « **on:** September 25, 2004, 05:00:02 pm »

anything I may need:

MP3 Player (portable)
Act Labs light Gun

or ca$h

I just finished a job for CrashWG and and can do some machining ( or a little sheetmatel work ). Just email me and let me know what you need and I will see if I would be able to make it for you.

i.e. brackets, mounting plates, marquee retainers etc... Let me know what you need and some measurements and gladly let you know if I can fabricate it.

I can work with stainless steel, aluminum, tool steel etc...

Hoagie_one · « **Reply #1 on:** September 25, 2004, 08:29:54 pm »

i need a metal cp made for me, just the rectangle with 4 bends in it. ill drill the holes myself.

what would somethin like that cost?

itismejs · « **Reply #2 on:** September 25, 2004, 08:48:32 pm »

hmmmm.I know I can get my hands on a dvd burner but I ahve no idea wat kinda metal work I would need done lol.

Maybe a 1p or 2p cp w/ holes for a portable I may make in the futureeeee.

GameDork · « **Reply #3 on:** September 25, 2004, 10:21:19 pm »

Quote from: Hoagie_one on September 25, 2004, 08:29:54 pm

i need a metal cp made for me, just the rectangle with 4 bends in it. ill drill the holes myself.

what would somethin like that cost?

What size we talkin? Could you give some specific diamensions?

I'll PM you about a price.

Hoagie_one · « **Reply #4 on:** September 28, 2004, 11:21:36 am »

ill get back to ya...gotta take measurments.

Madman · « **Reply #5 on:** September 28, 2004, 10:56:27 pm »

hey do you still need a dvd burner? I have a 2x burner to possibly trade for some work.
let me know!

GameDork · « **Reply #6 on:** September 29, 2004, 09:31:34 pm »

Quote from: Madman on September 28, 2004, 10:56:27 pm

hey do you still need a dvd burner? I have a 2x burner to possibly trade for some work.
let me know!

I sure do!! What kind of job you got?

PM me please.

itismejs · « **Reply #7 on:** September 29, 2004, 10:32:26 pm »

Bgnome · « **Reply #8 on:** September 30, 2004, 12:10:23 am »

thats pretty rough.. i dont think i can actually make sense out of that..

GameDork · « **Reply #9 on:** October 03, 2004, 04:23:16 pm »

I would rather not do larger sheetmetal work, I am more of a machinist but it never hurts to ask, I may be able to do apiece you need.

There is no minimum of pieces and I can do stuff MUCH cheaper than a regular machine shop would do.

itsmejs: Could you be a little more specific? that may a bit large for the equipment that I have access to.

HoagieOne: Anything?

Here's some stainless steel brackets I made for Crashwg:

GameDork · « **Reply #10 on:** October 03, 2004, 04:55:30 pm »

and a joystick mounting plate:

AmericanDemon · « **Reply #11 on:** October 03, 2004, 05:01:33 pm »

Thats some nice looking work there.

Hoagie_one · « **Reply #12 on:** October 04, 2004, 08:57:04 am »

sorry, havent had time to take measurments.

I will get back to you. I'll probably need 2 panels.

GameDork · « **Reply #13 on:** October 16, 2004, 03:37:15 am »

Bump....

etoasty · « **Reply #14 on:** October 17, 2004, 07:48:50 pm »

GameDork,
Do you have a metalbrake for at least 24" sheetmetal>

I need a piece of metal to fill the gap between my control panel and bezel. Bought a piece of Williams Control Panel molding trim but it's not quite as robust as i'd like.

Without measuring it, i basically need a 4x24" piece of 18 or so gauge sheetmetal bent at 90* along its long end 1" from the edge. Then about a 70* bend another inch below the first one (putting it 2" from either edge).

Essentially how it'd look from the ends:

| /
| /
| /
| /
|___________/

I'd do it myself, but i don't have a break, and i don't think i can as good an edge as i'd like using clamps.

Thanks

GameDork · « **Reply #15 on:** October 18, 2004, 01:43:52 pm »

Quote from: etoasty on October 17, 2004, 07:48:50 pm

GameDork,
Do you have a metalbrake for at least 24" sheetmetal>

I need a piece of metal to fill the gap between my control panel and bezel. Bought a piece of Williams Control Panel molding trim but it's not quite as robust as i'd like.

Without measuring it, i basically need a 4x24" piece of 18 or so gauge sheetmetal bent at 90* along its long end 1" from the edge. Then about a 70* bend another inch below the first one (putting it 2" from either edge).

Essentially how it'd look from the ends:

| /
| /
| /
| /
|___________/

I'd do it myself, but i don't have a break, and i don't think i can as good an edge as i'd like using clamps.

Thanks

Yeah, we have a brake that is about 10 feet long! It has been abused in the past. The top "clamp" has places in it where it has been rolled up by someone trying to bend, what looks like, round stock!

It will bend just fine, but the shhetmetal may have a few places in the bend where its just not quite as crisp of a bend.

If you want, give me the measurements and I'll bend one and send you a decent pic to llet you see if it will be ok.

As for price, I can do it for the cost of the sheetmetal,shipping and maybe a 5 dollars for my time.

itismejs · « **Reply #16 on:** October 18, 2004, 03:31:11 pm »

exibar · « **Reply #17 on:** October 19, 2004, 08:20:52 pm »

PM on the way ;-) and a bump for ya! :-)

GameDork · « **Reply #18 on:** March 05, 2005, 10:55:34 am »

Hey fellas, haven't been on here in a while.

My wife and I just had our first baby 8 weeks ago, been pretty busy.

anyway, I just finished a job for Hoagie_One and I can do some machine work for you guys again.

Just email me or PM what you might need made and I'll see if I can't get it done.

Here's a pic of some Cp's I did for Hoagie

Sorry bout the spics, it was with my cell phone

Hoagie_one · « **Reply #19 on:** March 05, 2005, 01:31:21 pm »

I'll post better pics when the package arrives.

Looking sharp so far though. I'm stoked. Just so everyone knows, this isnt just some bent metal. He made a base CP with studs and removable panels that set ont eh studs which can be tightened down and plated it too.

Lookin good.


Main	Restorations	Software	Audio/Jukebox/MP3	Everything Else	Buy/Sell/Trade
Project Announcements	Monitor/Video	GroovyMAME	Merit/JVL Touchscreen	Meet Up	Retail Vendors
Driving & Racing	Woodworking	Software Support Forums	Consoles	Project Arcade	Reviews
Automated Projects	Artwork	Frontend Support Forums	Pinball	Forum Discussion	Old Boards
Raspberry Pi & Dev Board	controls.dat	Linux	Miscellaneous Arcade	Wiki Discussion	Old Archives
Lightguns	Arcade1Up	Try the site in https mode		Site News


Unread posts \| New Replies \| Recent posts \| Rules \| Chatroom \| Wiki \| File Repository \| RSS \| Submit news