Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Trackball help please - old model, not sure how to connect  (Read 1552 times)

0 Members and 1 Guest are viewing this topic.

timsatari

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 49
  • Last login:August 31, 2020, 05:52:07 am
  • By the power of Greyskull!
Trackball help please - old model, not sure how to connect
« on: August 31, 2020, 12:01:01 am »
Hi all - moving through my very long-term old project and need some guidance please in relation to the trackball.

Truth is, I can't even remember where I purchased it from (maybe 10 years ago) and wish to use it now if possible.

Please see the images, the underside of the installed unit, it has 2 x 4 pin connectors.. I've taken one out to show the board.

How / what do I connect these to? I have two 4 pin connectors in my kit too... any assistance appreciated.

mahuti

  • Wiki Master
  • Trade Count: (0)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 2757
  • Last login:September 18, 2024, 01:16:22 pm
  • I dare anything! I am Skeletor!
Re: Trackball help please - old model, not sure how to connect
« Reply #1 on: August 31, 2020, 12:35:27 am »
I have one of these. I think maybe Ultimarc sold them for a short while. Anyway, I've attached a picture. The outside wires are 5v (red) and ground (black). The inside 2 wires are x/y take a look at the photo ive attached.

The wires themselves need to be attached to something like an OptiPac or Opti-Wiz or some other trackball/spinner encoder board.
« Last Edit: August 31, 2020, 12:39:02 am by mahuti »
Raspberry Pi, AttractMode, and Skeletor enthusiast.

PL1

  • Global Moderator
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9674
  • Last login:Today at 04:55:58 pm
  • Designated spam hunter
Re: Trackball help please - old model, not sure how to connect
« Reply #2 on: August 31, 2020, 12:49:46 am »
Found this pinout and note on the Ultimarc OptiPac page here, "installation" tab.

Quote
The track side of the PCB should look like this. If it is the "special" type for Mini-PAC it will have two extra resistors added to this side.

As Mahuti indicated, you'll need an optical encoder:
- Ultimarc Opti-Pac
- GGG OptiWiz
- Ultimarc I-Pac2 (2015 or newer)
- Ultimarc Mini-Pac
- Arduino with mouse firmware


Scott
« Last Edit: August 31, 2020, 12:54:28 am by PL1 »

timsatari

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 49
  • Last login:August 31, 2020, 05:52:07 am
  • By the power of Greyskull!
Re: Trackball help please - old model, not sure how to connect
« Reply #3 on: August 31, 2020, 05:52:24 am »
Thanks so much for the responses!