Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news


  

Author Topic: Makvision/WeiYa Vertical collapsed bootom only  (Read 287 times)

0 Members and 1 Guest are viewing this topic.

Rickn

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 474
Makvision/WeiYa Vertical collapsed bootom only
« on: October 07, 2018, 03:41:21 pm »
Like my last post I am swamped and am reaching out to help me not spend a lot of time on these odd balls.

In the past week I have taken on about 20 more board repairs and I was already had a 10 board list.

So if any one has seen this and has some insight, here is the scoop.

Chassis says Wei Ya Probably Makvion M3129DS-LGC2929D1-LG
Originally vertical colllapse, replaced the Vert output IC now good picture on top. Bottom is black and a bright Horizontal Line in the center... Complete bottom vertical foldover.

Will scope the vertical circuit next.

Any thoughts greatly appreciated... I need to catch up!

Thanks

Rick


Always happy to help.., for the best in displays
Rick Nieman
Rick@Niemandisplays.com
www.niemandisplays.com
1023 Rife Rd Cambridge, Ontario Canada N1R5S3
519-621-1722

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 5752
Re: Makvision/WeiYa Vertical collapsed bootom only
« Reply #1 on: October 07, 2018, 04:34:57 pm »
i have c67 marked down as oddball vertical fault in my repair notes, also the safety resistor and caps on the 24v supply- although you must have 24v or there would be no vertical

buttersoft

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 705
  • Is running at 15kHz
Re: Makvision/WeiYa Vertical collapsed bootom only
« Reply #2 on: October 07, 2018, 07:29:23 pm »
Got a schematic? Might help pick something preventing the vertical coil reversing polarity, i guess.

Rickn

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 474
Re: Makvision/WeiYa Vertical collapsed bootom only
« Reply #3 on: October 08, 2018, 12:41:32 pm »
Thanks Grant, if you have time please check your notes.. for the life of me I cannot find C67 either on the board or the schematic..

Odd as I can locate C68.


Yes I have what appears to be the right schematic.


May have to set it aside for now.

Thanks

Ric
Always happy to help.., for the best in displays
Rick Nieman
Rick@Niemandisplays.com
www.niemandisplays.com
1023 Rife Rd Cambridge, Ontario Canada N1R5S3
519-621-1722

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 5752
Re: Makvision/WeiYa Vertical collapsed bootom only
« Reply #4 on: October 08, 2018, 04:25:08 pm »
220nf 100v  on r107
thats if it a m3129 chassis, no idea on a m2929 chassis

Rickn

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 474
Re: Makvision/WeiYa Vertical collapsed bootom only
« Reply #5 on: October 08, 2018, 07:34:53 pm »
Thanks Grant, the 2 boards are use different vertical IC's. I expect the cap in yours is a small tantalum cap off of pin 1 of the TDA 1675. The board I have by memory is TDA 1672..yes these puppies can cause weird issues, not usually the bottom vertical foldover. tHE 2929d1 Uses a TDA 8172.

Thanks I will plug on!
Always happy to help.., for the best in displays
Rick Nieman
Rick@Niemandisplays.com
www.niemandisplays.com
1023 Rife Rd Cambridge, Ontario Canada N1R5S3
519-621-1722

  
 

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31