Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Generic USB joystick board - how to connect?  (Read 6127 times)

0 Members and 1 Guest are viewing this topic.

drabina

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 18
  • Last login:September 13, 2018, 04:28:58 pm
  • I want to build my own arcade controls!
Generic USB joystick board - how to connect?
« on: September 09, 2018, 03:28:09 pm »
I have a cheap generic USB board that came with my joystick and buttons. There are few K ports (K1-K4 and K11-K12) but some are labeled as TURBO, AUTO, CLR, MODE, AU, AR, AD, AL, ST, SE, R1, R2, L1, L2. My arcade has 1 joystick, 6 buttons on the control panel plus 3 buttons on the front panel. How do I connect everything? I am installing Recalbox on the Raspberry PI 2 to run the arcade. Does it matter which ports on the USB board I use or is all configured later in the software?

Titchgamer

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 4222
  • Last login:December 17, 2023, 08:05:48 am
  • I have a gaming addiction.....
Re: Generic USB joystick board - how to connect?
« Reply #1 on: September 09, 2018, 04:01:53 pm »

JDFan

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3448
  • Last login:March 03, 2025, 10:29:54 am
  • I want to build my own arcade controls!
Re: Generic USB joystick board - how to connect?
« Reply #2 on: September 09, 2018, 05:23:50 pm »
Upper left connector is for the USB cable that came with it to go from the board to your PC USB port

Joystick depends on if you have a 5-pin connector or 4 2 pin connector type - If 5 pin it goes into the 5-pin port to the right of the USB connector Or if 4 2 pin connectors they go into the 4 2 pin connectors to the right of that ( AU is Up , AR RIght, AL Left, AD down ) for the joystick directions.

THen for your Buttons those are the 12 2 pin connectors along the bottom - SO that is where you connect the 6 CP buttons and 3 front panel buttons ( then you set them up in MAME or what ever emulator you are using )

drabina

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 18
  • Last login:September 13, 2018, 04:28:58 pm
  • I want to build my own arcade controls!
Re: Generic USB joystick board - how to connect?
« Reply #3 on: September 10, 2018, 08:19:54 am »
Thanks! Got the USB controller working. Originally, I had the TURBO, MODE, etc buttons connected but after reading your replies, I have switched them to the lower part of the ports and was able to configure all the buttons in RetroPie.