Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: WTB: e-clip for Midway joystick (FOUND)  (Read 988 times)

0 Members and 1 Guest are viewing this topic.

RayB

  • I'm not wearing pants! HA!
  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 11279
  • Last login:July 10, 2025, 01:33:58 am
  • There's my post
    • RayB.com
WTB: e-clip for Midway joystick (FOUND)
« on: October 02, 2010, 03:32:18 pm »
I need an e-clip for a Ms Pac Man joystick. The shaft is way smaller than your typical Wico. Manual says "1/4".

Thanks


Got some. thanks.
« Last Edit: October 07, 2010, 11:39:49 pm by RayB »
NO MORE!!

Franco B

  • Trade Count: (+10)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3766
  • Last login:February 15, 2024, 09:14:06 am
Re: WTB: e-clip for Midway joystick
« Reply #1 on: October 02, 2010, 04:22:55 pm »
If you can measure or find out the groove size I can send you one FOC.

Encryptor

  • Trade Count: (+34)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1287
  • Last login:December 21, 2023, 08:01:18 pm
Re: WTB: e-clip for Midway joystick
« Reply #2 on: October 02, 2010, 08:34:48 pm »
I can do the same. I have a whole kid of them I bought at Harbor Freight.

Encryptor

RayB

  • I'm not wearing pants! HA!
  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 11279
  • Last login:July 10, 2025, 01:33:58 am
  • There's my post
    • RayB.com
Re: WTB: e-clip for Midway joystick
« Reply #3 on: October 03, 2010, 12:17:29 pm »
Thanks!

It's hard to measure this thing.

The shaft diameter is 1/4" or possibly as much as 9/32" if you want to be ultra precise.

The groove seems to be maybe 7/32"

The manual calls it 1/4 e-ring, so I'm assuming these things are measured based on the shaft, not the groove, and the ring is measured based on the inner diameter, not including the little bumps
« Last Edit: October 03, 2010, 12:37:06 pm by RayB »
NO MORE!!

Encryptor

  • Trade Count: (+34)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1287
  • Last login:December 21, 2023, 08:01:18 pm
Re: WTB: e-clip for Midway joystick
« Reply #4 on: October 03, 2010, 05:19:42 pm »
RayB

I believe I have a pacman stick in the basement. I'll check it and get the one that fits. PM me or email me your address and I'll send it to you.

Encryptor