Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: Help de-casing Mag Monitor!?  (Read 1733 times)

0 Members and 1 Guest are viewing this topic.

BillyJack

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 175
  • Last login:September 20, 2011, 12:13:50 pm
  • Must...paint...cab...! Must...buy...marquee..!
Help de-casing Mag Monitor!?
« on: June 20, 2003, 01:00:51 am »
I've got a Mag DJ920 and I've removed it from the plastic case.  There were 2 copper plates (strips) attached (with glue/tape) to the plastic casing.  One on the top, one on the bottom.  BOth have wires running to the inside of the monitor.  The glass itself has 2 pieces of the same copper at the top and bottom of the monitor.  What do I need to do with the two strips from the case?  I'm not sure what to do , as it's sparked once (I powered it off / unplugged quickly, however the sparking did not affect the picture.)  

Thank you so much for any help,

BillyJack
« Last Edit: June 20, 2003, 10:19:06 am by BillyJack »
Logged
Now I've had my head in an elephant, a hippo, and a giant sloth.
-Homer

spectre

  • -- banned --
  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 418
  • Last login:April 07, 2004, 08:45:11 am
  • -- banned --
Re:Help de-casing Mag Monitor!?
« Reply #1 on: June 20, 2003, 12:08:03 pm »
 "as it's sparked once (I powered it off / unplugged quickly"

don't decase a monitor while it's plugged in...
LMFAO
Logged
-- banned --

BillyJack

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 175
  • Last login:September 20, 2011, 12:13:50 pm
  • Must...paint...cab...! Must...buy...marquee..!
Re:Help de-casing Mag Monitor!?
« Reply #2 on: June 20, 2003, 12:16:37 pm »
Quote from: spectre on June 20, 2003, 12:08:03 pm
"as it's sparked once (I powered it off / unplugged quickly"

don't decase a monitor while it's plugged in...
LMFAO

I didn't decase the monitor while it was plugged in.  It was sitting there doing nothing then sparked.  I decased it, installed it, plugged it in, turned it on, about 30 seconds later it sparked.  I shut it down, fiddled with stuff, turned it back on to see if it was dead, it wasn't and it hasn't done anything since.

BillyJack
Logged
Now I've had my head in an elephant, a hippo, and a giant sloth.
-Homer

spectre

  • -- banned --
  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 418
  • Last login:April 07, 2004, 08:45:11 am
  • -- banned --
Re:Help de-casing Mag Monitor!?
« Reply #3 on: June 20, 2003, 05:56:46 pm »
ah, cuz u said after it sparked you unplugged it, but anyway...u probably shorted something out somehow, i dunno much about monitors sorry
Logged
-- banned --

BillyJack

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 175
  • Last login:September 20, 2011, 12:13:50 pm
  • Must...paint...cab...! Must...buy...marquee..!
Re:Help de-casing Mag Monitor!?
« Reply #4 on: June 23, 2003, 09:25:38 am »
Ha... easy fix...  the two scary strips were to help ground the tube etc...  They weren't touching properly, so I re-attached them and used a little electrical tape.  NO MORE PROBLEMS!!! WOO!  The sparking was caused by static buildup on the tube jumping to the copper strips.


BillyJack

Logged
Now I've had my head in an elephant, a hippo, and a giant sloth.
-Homer
Pages: [1]
  
Go Up
« previous next »