Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Pentranic 1131Dynamo cab Need some basic help with hook up and the likes  (Read 1262 times)

0 Members and 1 Guest are viewing this topic.

Dr Zero

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 360
  • Last login:November 08, 2018, 06:06:43 pm
  • Sunny Florida North
    • Drzero.org
Well I sent my board off to be fixed and there is apparently 2 additional boards that go with the main one (go figure) I found the one with the adjustment pots on it



There is another small board that is missing doing with power  :banghead: and there is the question of how to get power to the monitor if there another component missing?


I will upload some pics and maybe that will help some  :banghead:









Anyone with a dynamo cab willing to take some pic of the inside back of theirs for me, I just need some form of reference so I know what Im dealing with. Thanks!
« Last Edit: July 29, 2009, 12:29:13 pm by Dr Zero »
Manuals and info on Dynamo cabs!

qrz

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1056
  • Last login:October 24, 2015, 03:04:15 pm
  • wrangling electrons since 1978
not quite sure what ur asking .
if the board was sent out for repair , i'd assume u would be awaiting its return  :dunno
otherwise , all connections are to monitor pcb.....
pic:
1   pcb connections for "pot " board
2   red wire = deguassing coil 
3   yoke plug
4   video  to monitor
5   AC to monitor


Dr Zero

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 360
  • Last login:November 08, 2018, 06:06:43 pm
  • Sunny Florida North
    • Drzero.org
not quite sure what ur asking .
if the board was sent out for repair , i'd assume u would be awaiting its return  :dunno
otherwise , all connections are to monitor pcb.....
pic:
1   pcb connections for "pot " board
2   red wire = deguassing coil 
3   yoke plug
4   video  to monitor
5   AC to monitor



Yeah a real nice fellow who runs a repair place here in Florida called and said um are there some parts to this   :o and I'm like ummm no.... :-\

So he has a power board he we can use but I'm not sure about how to tie it in.

Ok I got
1
2
3 I know goes to the main board and there is a smaller board that goes to the tube

4 Ah I see that is the from the jamma harness to the main board got ya!

5 I have a concern with there is apparently another small board that the power goes to then to the main board?
There is also a wire that plugs into the power not sure if that comes with the board or that is missing also. That is where I'm kinda lost.

Also thanks for the help I am totally new to this so I had rather ask some dumb question than assume and ruin a monitor or curl my hair any more  :afro:



Added

here is a board that is close to the one I have

« Last Edit: July 29, 2009, 02:04:33 pm by Dr Zero »
Manuals and info on Dynamo cabs!