Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Mearuring a curved CRT tube  (Read 1455 times)

0 Members and 1 Guest are viewing this topic.

Ummon

  • Trade Count: (+13)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 5244
  • Last login:June 09, 2010, 06:37:18 pm
Mearuring a curved CRT tube
« on: December 26, 2008, 06:44:35 pm »
What I'm really wondering here is whether a curved CRT is measured along an 'ideal plane', or if the actual curved surface of the tube is measured? Because, if it's the latter, then for example a 19" curved tube would be smaller than a 19" flat tube.
Yo. Chocolate.


"Theoretical physics has been the most successful and cost-effective in all of science."

Stephen Hawking


People often confuse expressed observations with complaint, ridicule, or - even worse - self-pity.

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6177
  • Last login:Today at 04:42:10 am
Re: Mearuring a curved CRT tube
« Reply #1 on: December 26, 2008, 06:59:02 pm »
a 19" curved and 19" pure flat are the same as the measure is made as dead flat on the diagonal from corner to corner
the only real time the curvature comes into play is how it affects the bezel
i.e a nanao ms8-29fan in daytona use if replaced with a wei ya 2929 will leave a gap in the bezel---which is why happ supply a bezel filler with the makvision tri sync monitor that they champion as a replacement

Jack Burton

  • Trade Count: (+3)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1384
  • Last login:April 07, 2025, 02:12:05 pm
  • .
Re: Mearuring a curved CRT tube
« Reply #2 on: December 26, 2008, 07:13:48 pm »
Wouldn't a curved glass with a diagonal flat measurement of 19" have a slightly larger surface area than one that had a flat screen?  After all, the curved glass is taking a longer route to go between two points.


grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6177
  • Last login:Today at 04:42:10 am
Re: Mearuring a curved CRT tube
« Reply #3 on: December 26, 2008, 07:18:10 pm »
Wouldn't a curved glass with a diagonal flat measurement of 19" have a slightly larger surface area than one that had a flat screen?  After all, the curved glass is taking a longer route to go between two points.


yeah but it is not important as it does not affect the size of the actual tube

Jack Burton

  • Trade Count: (+3)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1384
  • Last login:April 07, 2025, 02:12:05 pm
  • .
Re: Mearuring a curved CRT tube
« Reply #4 on: December 27, 2008, 12:07:42 am »
So is the glass on the other side (the side inside the tube) flat on the other side?  I'm just curious, I've never broken apart a CRT.

Ummon

  • Trade Count: (+13)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 5244
  • Last login:June 09, 2010, 06:37:18 pm
Re: Mearuring a curved CRT tube
« Reply #5 on: December 28, 2008, 03:37:01 pm »
I think it's concave, because otherwise you'd have issues due to refraction. That might imply flat tubes are convex inside, though. Hmmm.
Yo. Chocolate.


"Theoretical physics has been the most successful and cost-effective in all of science."

Stephen Hawking


People often confuse expressed observations with complaint, ridicule, or - even worse - self-pity.

qrz

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1056
  • Last login:October 24, 2015, 03:04:15 pm
  • wrangling electrons since 1978
Re: Mearuring a curved CRT tube
« Reply #6 on: December 28, 2008, 07:59:32 pm »
So is the glass on the other side (the side inside the tube) flat on the other side?  I'm just curious, I've never broken apart a CRT.

it is the same as the face .  the reason flat crts have additional geometry circuitry, is due to the fact the electron beam will take a bit more time to reach the corners than center of screen.



some early tv crts ( < 1945 )  were round with a flat screen.   minor distortion was mostly ignored in those days.
see   http://www.earlytelevision.org/index.html

hey , a "good picture" was sometimes defined as seeing movement in the snow .   ;D

if anyone cares,  the oldest tv i've repaired to date was a 1948 zenith.  was a very interesting set !

qrz

« Last Edit: December 28, 2008, 09:37:09 pm by qrz »