Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Help me build a jig for repetative miter cuts?  (Read 2775 times)

0 Members and 1 Guest are viewing this topic.

dmworking247

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 305
  • Last login:July 14, 2024, 01:30:59 pm
Help me build a jig for repetative miter cuts?
« on: October 06, 2008, 08:47:47 am »
I'm potentially going to be building a LOT of control panel boxes. The beauty of the material I'm using is that its preprimed, prebevelled architrave.

The thing thats costing me the most time however is doing the 45' miter cuts.

I have:
  • A compound mitre saw (but its currently a rough blade that I don't want to keep changing, and I also dont have a spare A$100 for a 100-tooth blade).
  • A jigsaw (difficult to get EXACTLY 45' especially if I have to keep re-setting the tool to its regular 90'), and its also difficult to cut these panels in a perfect straight line without a jig/guide.
  • A router (trying to figure out a way that I could build a jig using a patern bit to make perfect repeatable miter cuts).

Here's an example of the 'boxes' I'm trying to make repeatedly. Note the mitre joins in each corner. The MDF is roughly 1/2" thick and 2 2/3" tall (I'm hopeless with imperial).



I'd like to be able to cut perfect 45' miter cuts for two 'set' lengths of MDF with a minimum of setup/configuration. Can anybody suggest the right tool/how I'd build a jig to make life easier?



nuka1195

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 148
  • Last login:April 18, 2020, 08:47:25 pm
Re: Help me build a jig for repetative miter cuts?
« Reply #1 on: October 06, 2008, 10:11:32 am »
1. miter saw with a stop block
2. router mounted in a table with a 45 degree bit and a miter gauge.

dmworking247

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 305
  • Last login:July 14, 2024, 01:30:59 pm
Re: Help me build a jig for repetative miter cuts?
« Reply #2 on: October 06, 2008, 08:26:28 pm »
Ah! For some reason I had never thought about a 45' bit for the router (duh!). Thats given me something to think about, thanks!

Franco B

  • Trade Count: (+10)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 3766
  • Last login:February 15, 2024, 09:14:06 am
Re: Help me build a jig for repetative miter cuts?
« Reply #3 on: October 07, 2008, 10:48:11 am »
I was racking my brains trying to think up a way for you cut them with a router, I had never thought about a 45 degree bit either! Good plan :)

Twinpanther

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 40
  • Last login:January 12, 2016, 02:03:51 pm
  • Yukihime
Re: Help me build a jig for repetative miter cuts?
« Reply #4 on: October 07, 2008, 12:54:35 pm »
And if you wanna be fancy.

45° Lock Miter Bit
OMG, where have you guys been all my life?!

Blanka

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2248
  • Last login:January 25, 2018, 03:19:28 pm
Re: Help me build a jig for repetative miter cuts?
« Reply #5 on: October 07, 2008, 02:09:51 pm »
And if you wanna be fancy.

45° Lock Miter Bit

But with a lock bit, it won't work on the rounded edges. The joint won't be OK.

nuka1195

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 148
  • Last login:April 18, 2020, 08:47:25 pm
Re: Help me build a jig for repetative miter cuts?
« Reply #6 on: October 07, 2008, 03:52:56 pm »
it should work fine, just round after putting it together.

Blanka

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2248
  • Last login:January 25, 2018, 03:19:28 pm
Re: Help me build a jig for repetative miter cuts?
« Reply #7 on: October 08, 2008, 03:19:30 pm »
it should work fine, just round after putting it together.

The beauty of the material I'm using is that its preprimed, prebevelled architrave.

 :applaud:

nuka1195

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 148
  • Last login:April 18, 2020, 08:47:25 pm
Re: Help me build a jig for repetative miter cuts?
« Reply #8 on: October 08, 2008, 03:55:44 pm »
i still don't see an issue, plus glue ups with that router bit should be easier.

Blanka

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2248
  • Last login:January 25, 2018, 03:19:28 pm
Re: Help me build a jig for repetative miter cuts?
« Reply #9 on: October 08, 2008, 04:19:40 pm »
If it is pre-bevelled, you cannot make nice connections with the lock bit!
This is what will happen:

Blanka

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2248
  • Last login:January 25, 2018, 03:19:28 pm
Re: Help me build a jig for repetative miter cuts?
« Reply #10 on: October 08, 2008, 04:24:03 pm »

This is probably easiest for quick perfect 45 degree mitters (with the not shown angle-guide attached, or by turning the table in 45 degrees)
A table saw is also perfect for it, but it is harder to get the length of the parts perfect to the last 1/5th mm.
Guess I was half the time behind this machine when making the graduation town plan models  :laugh:
« Last Edit: October 08, 2008, 04:26:44 pm by Blanka »

shardian

  • Saint is the evil mastermind
  • Trade Count: (+23)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 9218
  • Last login:August 21, 2015, 03:11:31 pm
  • Friends don't let friends build frankenpanels...
Re: Help me build a jig for repetative miter cuts?
« Reply #11 on: October 10, 2008, 09:53:32 am »
Your Miter saw is the absolute best option for this. All you need is to rig up a stop block. Set up the block once, adjust the saw once, then bang out 100 pieces in 15 minutes. It is worth investing in a decent blade.