Author Topic: My first monitor problem. Blown fuse on PCB. (Read 1693 times)

mccoy178 · « **on:** November 02, 2006, 04:13:26 pm »

I bought a Street Fighter 2 cabinet and it didn't work. I did find a blown fuse on the pcb board of the monitor where the red power wires going to the monitor connect. I replaced the fuse, and when plugged back in, it just began to start when the fuse blew again. What other information can I provide to help on this? I can do some problem solving, I just need some tips on what to test or look for. Thanks for your help in advance.

grantspain · « **Reply #1 on:** November 02, 2006, 04:31:16 pm »

is the fuse the correct rating and is it blowing black

D_Zoot · « **Reply #2 on:** November 02, 2006, 04:34:52 pm »

Quote from: mccoy178 on November 02, 2006, 04:13:26 pm

What other information can I provide to help on this?

Make/model of the monitor would be a huge help, many of us can tell you what common issues are for various monitors, but we need to know what the monitor is first

There should be a decal somewhere on the monitor (NOT the decal on the back of the tube) with some ID information. If there isn't anything to identify it, post a picture of the board.

D

mccoy178 · « **Reply #3 on:** November 02, 2006, 04:52:58 pm »

Okay, here is what I have since discovered. The fuse is a 4A 125V and it is blowing black. It is located by the degaussing coil and not the power like I had first stated. Next, I pulled the board after discharging the monitor and it is a Kortek chassis # KTA-915. Does that help?

grantspain · « **Reply #4 on:** November 02, 2006, 05:04:32 pm »

not knowing the full history its difficult to say whats happening BUT always when a fuse blows pooless it points towards a dead short on the primary a/c psu circuit,in other words its most likely to be the degauss coil,degauss ptc component or the bridge rectifier circuit
start by unplugging the degauss coil,then meter the bridge circuit then desolder the ptc component(thats the black or white plastic box like component with three legs that the degauss coil goes directly to),oh and make sure you have lots of fuses

mccoy178 · « **Reply #5 on:** November 02, 2006, 05:08:46 pm »

I did test the monitor with the degaussing coil unplugged and the gun control cable unplugged.

grantspain · « **Reply #6 on:** November 03, 2006, 03:03:52 am »

then go to the next thing i suggested

mccoy178 · « **Reply #7 on:** November 03, 2006, 03:19:49 am »

Will do. Just keeping you updated. I will have more to report on Monday.


Main	Restorations	Software	Audio/Jukebox/MP3	Everything Else	Buy/Sell/Trade
Project Announcements	Monitor/Video	GroovyMAME	Merit/JVL Touchscreen	Meet Up	Retail Vendors
Driving & Racing	Woodworking	Software Support Forums	Consoles	Project Arcade	Reviews
Automated Projects	Artwork	Frontend Support Forums	Pinball	Forum Discussion	Old Boards
Raspberry Pi & Dev Board	controls.dat	Linux	Miscellaneous Arcade	Wiki Discussion	Old Archives
Lightguns	Arcade1Up	Try the site in https mode		Site News


Unread posts \| New Replies \| Recent posts \| Rules \| Chatroom \| Wiki \| File Repository \| RSS \| Submit news

Author Topic: My first monitor problem. Blown fuse on PCB. (Read 1693 times)

mccoy178

My first monitor problem. Blown fuse on PCB.

grantspain

Re: My first monitor problem. Blown fuse on PCB.

D_Zoot

Re: My first monitor problem. Blown fuse on PCB.

mccoy178

Re: My first monitor problem. Blown fuse on PCB.

grantspain

Re: My first monitor problem. Blown fuse on PCB.

mccoy178

Re: My first monitor problem. Blown fuse on PCB.

grantspain

Re: My first monitor problem. Blown fuse on PCB.

mccoy178

Re: My first monitor problem. Blown fuse on PCB.