July 03, 2025, 02:31:22 pm
Home
Help
Search
Login
Register
News:
Support this site
Shop
Amazon Arcade Stuff
through our link. Thank you!
Forum notices to gmail.com addresses are working. Microsoft addresses are still not.
The NEW Build Your Own Arcade Controls
|
Main
|
Monitor/Video Forum
|
Just replaced my chassis Now all I get is a single vertical stripe
Main
Restorations
Software
Audio/Jukebox/MP3
Everything Else
Buy/Sell/Trade
Project Announcements
Monitor/Video
GroovyMAME
Merit/JVL Touchscreen
Meet Up
Retail Vendors
Driving & Racing
Woodworking
Software Support Forums
Consoles
Project Arcade
Reviews
Automated Projects
Artwork
Frontend Support Forums
Pinball
Forum Discussion
Old Boards
Raspberry Pi & Dev Board
controls.dat
Linux
Miscellaneous Arcade
Wiki Discussion
Old Archives
Lightguns
Arcade1Up
Try the site in https mode
Site News
Unread posts
|
New Replies
|
Recent posts
|
Rules
|
Chatroom
|
Wiki
|
File Repository
|
RSS
|
Submit news
« previous
next »
Send this topic
Print
Pages: [
1
]
Go Down
Author
Topic: Just replaced my chassis Now all I get is a single vertical stripe (Read 1928 times)
0 Members and 1 Guest are viewing this topic.
xteeejx
Trade Count:
(
0
)
Full Member
Offline
Posts: 16
Last login:November 22, 2006, 12:08:19 pm
Just replaced my chassis Now all I get is a single vertical stripe
«
on:
April 06, 2006, 02:26:01 am »
Hey Guys,
I just replaced my Hantarex chassis with a Wei Ya from Alva. I powered it up and nothing exploded
but all I get is a single vertical line in the center on the monitor. I can see a little bit of street fighter vs capcom going on in my single line but it's still not too useful. I tried switching around the rgb cables but that didn't help. Any Ideas what might be going on?
I tried searching but didn't find anything that seemed to apply.
Thanks a lot! This site has been really helpful!
-TJ
Logged
grantspain
I personally prefer "bog trotter"
Trade Count:
(
+1
)
Full Member
Offline
Posts: 6177
Last login:July 01, 2025, 09:49:46 am
Re: Just replaced my chassis Now all I get is a single vertical stripe
«
Reply #1 on:
April 06, 2006, 04:49:23 am »
something to do with your scan coils by the looks of it.
Logged
Ken Layton
Guru
Trade Count:
(
+1
)
Full Member
Offline
Posts: 7061
Last login:October 12, 2021, 12:25:59 am
Technician
Re: Just replaced my chassis Now all I get is a single vertical stripe
«
Reply #2 on:
April 06, 2006, 11:22:35 am »
I assume you measured the Hantarex's yoke resistance before ordering the Wei-ya replacement? This was done to ensure you ordered the correct chassis.
Hantarex used a different color scheme for their yoke wiring:
Brown and red wires are the vertical deflection section on the yoke.
Orange and yellow wires are the horizontal deflection section on the yoke.
The replacement chassis has the standardized yoke color scheme of red & blue for horizontal section and green & yellow for vertical section.
«
Last Edit: April 12, 2006, 06:52:29 pm by Ken Layton
»
Logged
xteeejx
Trade Count:
(
0
)
Full Member
Offline
Posts: 16
Last login:November 22, 2006, 12:08:19 pm
Re: Just replaced my chassis Now all I get is a single vertical stripe
«
Reply #3 on:
April 12, 2006, 01:03:51 pm »
Hey, thanks for the replies.
I remeasured the vertical resistance and got 5.5 Ohms. Raul at Alva says the 826HR chassis I bought will work with 5.5. Am I missing something? Do you guys think this might be a yoke or tube problem? Or is it more likely that I somehow messed up the chassis during the install process. Maybe my isolation transformer?
Thanks a lot you guys, I have no idea what I'm doing
Logged
Ken Layton
Guru
Trade Count:
(
+1
)
Full Member
Offline
Posts: 7061
Last login:October 12, 2021, 12:25:59 am
Technician
Re: Just replaced my chassis Now all I get is a single vertical stripe
«
Reply #4 on:
April 12, 2006, 06:56:31 pm »
Are you sure the yoke wires are connected properly to the new chassis? Remember the color code is different (Hantarex always had to be different than everyone else).
This link shows how the 826 chassis is connected to a Wells-Gardner monitor but it should give you some guidance with your Hantarex:
http://home.earthlink.net/~arcadeparts/id11.html
Logged
xteeejx
Trade Count:
(
0
)
Full Member
Offline
Posts: 16
Last login:November 22, 2006, 12:08:19 pm
Re: Just replaced my chassis Now all I get is a single vertical stripe
«
Reply #5 on:
April 13, 2006, 04:35:14 am »
Alright that was it, I had everything wired in reverse, thanks Ken. Everything's working perfectly with my streetfighter pcb, the monitor pops when I try to load up the mame machine, but I think it's a driver issue.
Thanks Again!
-TJ
Logged
Send this topic
Print
Pages: [
1
]
Go Up
« previous
next »
The NEW Build Your Own Arcade Controls
|
Main
|
Monitor/Video Forum
|
Just replaced my chassis Now all I get is a single vertical stripe