Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: OPTIPAC PROBLEM- AGGHRRR!  (Read 1591 times)

0 Members and 1 Guest are viewing this topic.

the3eyedblindman

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 665
  • Last login:November 17, 2006, 03:00:06 pm
  • Soon: 4 Player Mame and Scratch Built Moonwalker.
OPTIPAC PROBLEM- AGGHRRR!
« on: August 22, 2005, 07:07:50 pm »
My cabinet is completely done....my control panel is completely wired and done...I have one more thing to do and i can finally be done...and..... My trackball wont work! AHH! I have an ultimarc 2 and 1/4 inch trackball with the ultimarc optipac. I have the optipac getting power from the ipac via the supplied cable, and the mouse buttons work....so I know its recieving power, but  when I move the ball my cursor wont move! the computer recognizes the serial mouse (im using a serial optipac) but for some reason the cursor wont move. I have checked all my wire connections and they are right, I dont know whats goin on! I just wanna finish the CABINET!!!! >:(
Logged
Coming soon: 4 player mame cab and Scratch built Moonwalker....Hall of Fame, here I come!

whammoed

  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2312
  • Last login:June 02, 2026, 10:49:42 am
  • Crack don't smoke itself
    • NiceMite
Re: OPTIPAC PROBLEM- AGGHRRR!
« Reply #1 on: August 22, 2005, 07:15:38 pm »
I had the same problem with my ultimarc trackball.  It was the wiring harnesses.  The wires weren't making contact.  Take a very small flathead screwdriver and push the wires further into the red harnesses.  You may have the same issue.
Logged

the3eyedblindman

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 665
  • Last login:November 17, 2006, 03:00:06 pm
  • Soon: 4 Player Mame and Scratch Built Moonwalker.
Re: OPTIPAC PROBLEM- AGGHRRR!
« Reply #2 on: August 22, 2005, 10:32:59 pm »
Do I push the wires inward or down towards the top of the ball?
Logged
Coming soon: 4 player mame cab and Scratch built Moonwalker....Hall of Fame, here I come!

whammoed

  • Trade Count: (+4)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2312
  • Last login:June 02, 2026, 10:49:42 am
  • Crack don't smoke itself
    • NiceMite
Re: OPTIPAC PROBLEM- AGGHRRR!
« Reply #3 on: August 23, 2005, 09:38:33 am »
Quote from: the3eyedblindman on August 22, 2005, 10:32:59 pm
Do I push the wires inward or down towards the top of the ball?
Down toward the ball.  Take a close look at the connector.  There are little blades that cut past the insulation to make contact with the wire.  If the wire isn't pushed down far enough, the connection can loose contact.
Logged
Pages: [1]
  
Go Up
« previous next »