Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: makvision 2929 blowing HOT  (Read 1414 times)

0 Members and 1 Guest are viewing this topic.

RichSorr

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 180
  • Last login:August 29, 2015, 07:27:00 pm
makvision 2929 blowing HOT
« on: August 14, 2015, 08:19:42 am »
I have a makvision C2929D that keeps blowing the HOT and burning up the 1k resistor at R68. Any suggestions as where to look next?

When I turned it on after replacing those parts I got a high pitched squeal and a few clicks followed by a puff of smoke from the resistor.

any help is appreciated
« Last Edit: August 14, 2015, 08:28:31 am by RichSorr »
Logged

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6177
  • Last login:July 16, 2025, 06:33:55 pm
Re: makvision 2929 blowing HOT
« Reply #1 on: August 14, 2015, 01:24:42 pm »
check q20
this could be flyback
Logged

RichSorr

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 180
  • Last login:August 29, 2015, 07:27:00 pm
Re: makvision 2929 blowing HOT
« Reply #2 on: August 14, 2015, 01:52:06 pm »
q20 seems OK. The HOT shorts immediately and the resistor smokes, but isn't an instant failure. d21 is fine also.

I
Logged

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6177
  • Last login:July 16, 2025, 06:33:55 pm
Re: makvision 2929 blowing HOT
« Reply #3 on: August 14, 2015, 02:12:42 pm »
check the high voltage caps at c81 and c75
Logged

RichSorr

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 180
  • Last login:August 29, 2015, 07:27:00 pm
Re: makvision 2929 blowing HOT
« Reply #4 on: August 18, 2015, 07:29:28 pm »
no luck with those caps. I replaced everything once more and still have R68 smoking with some high pitch whines and clicking. Oddly enough I pulled the HOT off and it tested fine this time around.
Logged

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6177
  • Last login:July 16, 2025, 06:33:55 pm
Re: makvision 2929 blowing HOT
« Reply #5 on: August 18, 2015, 08:25:23 pm »
i would be looking at flyback but i do not have much experience with these chassis so maybe someone else can help further
Logged

RichSorr

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 180
  • Last login:August 29, 2015, 07:27:00 pm
Re: makvision 2929 blowing HOT
« Reply #6 on: August 23, 2015, 12:53:19 pm »
I couldn't put anymore time into it. Installed a 26" LCD and will save the chassis for a rainy day. thanks for the help
Logged
Pages: [1]
  
Go Up
« previous next »