Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: Wells Gardner Help needed  (Read 1210 times)

0 Members and 1 Guest are viewing this topic.

mustang

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 8
  • Last login:December 30, 2014, 09:34:55 am
Wells Gardner Help needed
« on: September 12, 2014, 01:26:06 pm »
Hi
I have a W/G 2792 I bought as a non runner.
I found some tracks burnt and repaired them.


Could some expert on these  tell me please where to look next?

The image is compressed into a vertical strip as you can see.

Many thanks
Martin

Logged

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6177
  • Last login:July 16, 2025, 06:33:55 pm
Re: Wells Gardner Help needed
« Reply #1 on: September 13, 2014, 05:35:17 am »
do you have a photo of the chassis?
Logged

mustang

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 8
  • Last login:December 30, 2014, 09:34:55 am
Re: Wells Gardner Help needed
« Reply #2 on: September 13, 2014, 01:05:55 pm »
Here you go Grant:

Logged

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6177
  • Last login:July 16, 2025, 06:33:55 pm
Re: Wells Gardner Help needed
« Reply #3 on: September 13, 2014, 05:33:05 pm »
right so it is a d9200
check out the wg repair guide-"no horizontal scan"
http://www.wellsgardner.com/pdf/Repair/D9200_27_33_39_inch.pdf
Logged

mustang

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 8
  • Last login:December 30, 2014, 09:34:55 am
Re: Wells Gardner Help needed
« Reply #4 on: September 14, 2014, 03:12:48 am »
Thanks Grant yes its a 9200.

Would you have a schematic for it?


Martin

Logged

grantspain

  • I personally prefer "bog trotter"
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 6177
  • Last login:July 16, 2025, 06:33:55 pm
Re: Wells Gardner Help needed
« Reply #5 on: September 14, 2014, 04:23:18 am »
the schematic is on the wells gardner service site
Logged

mustang

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 8
  • Last login:December 30, 2014, 09:34:55 am
Re: Wells Gardner Help needed
« Reply #6 on: September 16, 2014, 11:45:30 am »
Ta
Logged
Pages: [1]
  
Go Up
« previous next »