Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: 25" K7000 Help  (Read 2391 times)

0 Members and 1 Guest are viewing this topic.

Devryn

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 15
  • Last login:May 28, 2011, 10:53:15 am
25" K7000 Help
« on: February 26, 2011, 04:52:30 pm »
What it's doing now:


Series of events:
1.  Blew fuses.
2.  Sent to member on KLOV for refurbishment.  He replaced flyback, D20, D21, and R103.
3.  I got it back, plugged it in on my bench and it worked great.
4.  I put it in the cabinet, but forgot to reconnect anode cap.  It arced from somewhere.
5.  It was blowing fuses again.
6.  Replaced D20, D21 (with 1N4005), VR, and HOT
7.  It gave a scrambled picture.
8.  Replaced IC3
9.  Now its doing what I linked to.

Help.  :(
« Last Edit: February 26, 2011, 05:05:08 pm by Devryn »

Naukuga

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 8
  • Last login:March 02, 2011, 02:37:58 am
Re: 25" K7000 Help
« Reply #1 on: February 26, 2011, 05:14:51 pm »
Check your monitor ground! i had a screen that was doing something similar, and i ended up finding the ground wire wasnt hooked up right. My board arced to the frame and fried.

Devryn

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 15
  • Last login:May 28, 2011, 10:53:15 am
Re: 25" K7000 Help
« Reply #2 on: February 26, 2011, 05:29:18 pm »
Check your monitor ground! i had a screen that was doing something similar, and i ended up finding the ground wire wasnt hooked up right. My board arced to the frame and fried.
Ground wire from the tube to the neckboard seems fine.

Kevin Mullins

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 4504
  • Last login:February 01, 2021, 01:29:34 pm
    • Me on Myspace
Re: 25" K7000 Help
« Reply #3 on: February 26, 2011, 05:36:49 pm »
Have you tried adjusting the Horizontal Hold and 50/60Hz pots ?
Is the SYNC wired connected properly on the video cable ?
Not a technician . . . . just a DIY'er.

Devryn

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 15
  • Last login:May 28, 2011, 10:53:15 am
Re: 25" K7000 Help
« Reply #4 on: February 26, 2011, 06:10:34 pm »
None of the pots make much difference.  The rgb and sync are hooked up:
Rgb--- g-s

Devryn

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 15
  • Last login:May 28, 2011, 10:53:15 am
Re: 25" K7000 Help
« Reply #5 on: February 26, 2011, 06:59:28 pm »
Is there any chance that the Diodes I replaced are causing this?  The 1N4005's are 1 Amp 600 Volt.  I believe that the 1N5061's that were in there were 3 Amp 600 Volt...

qrz

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1056
  • Last login:October 24, 2015, 03:04:15 pm
  • wrangling electrons since 1978
Re: 25" K7000 Help
« Reply #6 on: February 26, 2011, 08:12:19 pm »
the diodes should be replaced with proper ratings .
HOT chassis  ! must use isolation xformer .

d21,22 would be a frequent failure without isolation
C57 is a common failure
also check c23

and check sync/H hold per Kevin  ;D

Devryn

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 15
  • Last login:May 28, 2011, 10:53:15 am
Re: 25" K7000 Help
« Reply #7 on: February 26, 2011, 08:24:43 pm »
Diode ratings are in accordance with service manual.  Already checked sync.

Kevin Mullins

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 4504
  • Last login:February 01, 2021, 01:29:34 pm
    • Me on Myspace
Re: 25" K7000 Help
« Reply #8 on: February 26, 2011, 10:38:08 pm »
Do you have another game you can hook up to that monitor?
Or vice versa, take that game and connect to a different monitor?

Just to verify if it is a monitor problem or if it is a game pcb problem.
Wanna make sure you didn't zap the game pcb and knock something out in the video ouput section.
Not a technician . . . . just a DIY'er.

Devryn

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 15
  • Last login:May 28, 2011, 10:53:15 am
Re: 25" K7000 Help
« Reply #9 on: February 26, 2011, 10:57:04 pm »
I don't.  :(