Software Support > GroovyMAME
New CRT Emudriver/VMMaker/Arcade OSD download, documentation and discussion site
Calamity:
--- Quote from: Sledge on February 18, 2017, 07:36:21 am ---
--- Quote from: Calamity on February 18, 2017, 07:32:18 am ---
--- Quote from: Sledge on February 18, 2017, 02:11:22 am ---Is arcade15 good enough?
Should i worry about trying to use MS929?
--- End quote ---
You can probably stick to arcade_15 if you're anyway removing upper ranges. You should be getting a normal desktop with ms929 anyway. All what matters is the resolution that ends up being applied to the desktop.
--- End quote ---
Which i can't actually see what it is as it's too squished, so ok, i'll stick to arcade15
But what settings do i use for a vertical screen?
--- End quote ---
There's always a way. Arcade OSD will tell you.
iRotate is not needed anymore, you can set portrait mode directly from Windows screen options. Please understand that saying "things go bad" is a bit too unspecific.
(if you're going to rotate your desktop, make sure the correct check is applied in VMMaker dialog)
lettuce:
--- Quote from: Calamity on February 10, 2017, 03:22:09 pm ---
--- Quote from: patpittoulai on February 09, 2017, 09:18:47 pm ---Wow. so does that mean Radeon R9 series graphics card are now supported? Cool!
--- End quote ---
Yep. Using one here right now.
--- End quote ---
Is there any downside to using a more recent card than an older one?. I know a few years back the older cards could support lower resolutions than more recent cards is that still the case?
Sledge:
--- Quote from: Calamity on February 18, 2017, 07:46:29 am ---
--- Quote from: Sledge on February 18, 2017, 07:36:21 am ---
--- Quote from: Calamity on February 18, 2017, 07:32:18 am ---
--- Quote from: Sledge on February 18, 2017, 02:11:22 am ---Is arcade15 good enough?
Should i worry about trying to use MS929?
--- End quote ---
You can probably stick to arcade_15 if you're anyway removing upper ranges. You should be getting a normal desktop with ms929 anyway. All what matters is the resolution that ends up being applied to the desktop.
--- End quote ---
Which i can't actually see what it is as it's too squished, so ok, i'll stick to arcade15
But what settings do i use for a vertical screen?
--- End quote ---
Please understand that saying "things go bad" is a bit too unspecific.
(if you're going to rotate your desktop, make sure the correct check is applied in VMMaker dialog)
--- End quote ---
Well.. do we still use super resolutions for a vertical screen?
When i do that VMM only creates 3 modes, all of which are interlaced..
http://puu.sh/u9Dtw/b38fe71998.jpg
http://puu.sh/u9E0R/29a6e0d1f4.jpg
http://puu.sh/u9E8D/bf110e90fe.jpg
Calamity:
--- Quote from: Sledge on February 18, 2017, 11:18:12 pm ---Well.. do we still use super resolutions for a vertical screen?
When i do that VMM only creates 3 modes, all of which are interlaced..
--- End quote ---
Yes, super resolutions work for the vertical case. But you need to specify your monitor as "rotating to the right" or "rotating to the left". Also, don't forget to mark: "Desktop rotates too".
Sledge:
--- Quote from: Calamity on February 19, 2017, 03:22:04 pm ---
--- Quote from: Sledge on February 18, 2017, 11:18:12 pm ---Well.. do we still use super resolutions for a vertical screen?
When i do that VMM only creates 3 modes, all of which are interlaced..
--- End quote ---
Yes, super resolutions work for the vertical case. But you need to specify your monitor as "rotating to the right" or "rotating to the left". Also, don't forget to mark: "Desktop rotates too".
--- End quote ---
Ok, all sorted then..
So what's 'vertical fixed' for then? (i was choosing that as i never rotate my screen)
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version