Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: Sourcing Metal for control panels  (Read 2044 times)

0 Members and 1 Guest are viewing this topic.

Generic Eric

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 4520
  • Last login:July 15, 2024, 09:18:25 pm
  • Restore! Don't maim for MAME, build from scratch!
    • forum.arcadecontrols.com/index.php/topic,143226.0.html
Sourcing Metal for control panels
« on: December 14, 2014, 10:02:42 pm »
Is it possible that metal of a side panel of a dryer, stove or washing machine would be thick enough for a control panel?
Logged

BorgDog

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 436
  • Last login:August 22, 2021, 02:22:52 pm
  • Not a hipster for over 50 years!
Re: Sourcing Metal for control panels
« Reply #1 on: December 14, 2014, 10:59:03 pm »
i would say old ones would be fine, newer appliances not so much.   :angry:
Logged
My Projects:
MisSpent Youth a Vigolix bartop,  Little Bastard a rotating tablet/display bartop,
Pin-Dog a mini pin-cab on vpforums.org  Star Wars a wedgehead pincab on vpinball.com

AzureKnight

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 474
  • Last login:May 29, 2022, 12:22:17 am
Re: Sourcing Metal for control panels
« Reply #2 on: December 15, 2014, 10:13:32 am »

I would guess no.  When you lightly push on most washer/dryers that I have seen the "pop" in and out pretty easily and make quite a thundery racket.

Maybe if you double up a couple of sheets?
Logged

Vigo

  • the Scourage of Carpathia
  • Global Moderator
  • Trade Count: (+24)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 6417
  • Last login:June 05, 2025, 05:38:45 pm
Re: Sourcing Metal for control panels
« Reply #3 on: December 15, 2014, 12:36:43 pm »
I think size of panel, and if you are bending the metal at any spot would make a difference as well. I would think you could easily reinforce it in key areas as well. 
Logged

jennifer

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2895
  • Last login:August 11, 2023, 06:24:58 am
Re: Sourcing Metal for control panels
« Reply #4 on: December 16, 2014, 01:10:14 am »
    Your local HVAC guy will have scraps of 16ga. you can pick through.... That or your local metal outlet, they always have a wall of bargain leftovers.
Logged
Pages: [1]
  
Go Up
« previous next »