Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: Advice on metal control panel thickness.  (Read 1320 times)

0 Members and 1 Guest are viewing this topic.

Apollo

  • Yes You Can Have A Custom Title
  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1877
  • Last login:May 27, 2021, 10:49:02 pm
    • Eight Bells
Advice on metal control panel thickness.
« on: April 15, 2004, 07:42:48 pm »
I am ordering my control panels from the steel fabricators tomorrow and am considering ordering them in 2mm mild steel and then powder coating them. The dimensions are 66cm wide by 34cm deep. Does anyone see any problems with this?
Thankyou.
Logged

SirPeale

  • Green Mountain Man
  • Global Moderator
  • Trade Count: (+23)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 12963
  • Last login:August 04, 2023, 09:51:57 am
  • Arcade Repair in New England
    • Arcade Game and Other Coin-Op Projects
Re:Advice on metal control panel thickness.
« Reply #1 on: April 15, 2004, 08:20:16 pm »
2 MM???  That sound excessive.  16G is the norm, IIRC.
Logged

Apollo

  • Yes You Can Have A Custom Title
  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1877
  • Last login:May 27, 2021, 10:49:02 pm
    • Eight Bells
Re:Advice on metal control panel thickness.
« Reply #2 on: April 15, 2004, 08:27:20 pm »
Would that be about 1.5mm? That's the thickness I used for my mounting polates on my last CP and that was pretty sturdy.
Logged

SirPeale

  • Green Mountain Man
  • Global Moderator
  • Trade Count: (+23)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 12963
  • Last login:August 04, 2023, 09:51:57 am
  • Arcade Repair in New England
    • Arcade Game and Other Coin-Op Projects
Re:Advice on metal control panel thickness.
« Reply #3 on: April 15, 2004, 09:05:12 pm »
Honestly, I have no clue.  Let's see if Google has an answer:

Let's see, I found this:

http://www.geocities.com/shridhar_prabhu/gauge-cov.html

Which states that 16G is .060 in steel.  According to another site, that's 1.5MM.  So yes, you're right!
Logged

Apollo

  • Yes You Can Have A Custom Title
  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1877
  • Last login:May 27, 2021, 10:49:02 pm
    • Eight Bells
Re:Advice on metal control panel thickness.
« Reply #4 on: April 15, 2004, 09:10:28 pm »
Groovy, thanks Peale you r a star!
Logged

Stingray

  • Official Slacker - I promise to try a lot less
  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 10462
  • Last login:April 08, 2021, 03:43:54 pm
Re:Advice on metal control panel thickness.
« Reply #5 on: April 16, 2004, 01:32:46 pm »
I used 18 guage, but only because that's what I had handy.

-S
Logged
Quote from: releasedtruth on November 02, 2006, 04:25:16 pm
Stingray you magnificent bastard!
Quote from: Hoopz on October 24, 2012, 02:04:03 pm
This place is dead lately.  Stingray scare everyone off?

Apollo

  • Yes You Can Have A Custom Title
  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 1877
  • Last login:May 27, 2021, 10:49:02 pm
    • Eight Bells
Re:Advice on metal control panel thickness.
« Reply #6 on: April 16, 2004, 07:42:12 pm »
Ok went to the steel people today and after looking at 1.5mm and 2mm I went with the 2mm. Thanks for input folks. 1.5mm was just a little too flexible.
Logged
Pages: [1]
  
Go Up
« previous next »