fooling with m2emu network

Main > Driving & Racing Cabinets

<< < (54/68) > >>

SailorSat:

--- Quote from: MrThunderwing on October 29, 2023, 12:30:27 pm ------fudgesicle--- me sideways - where has that time gone?!?

--- End quote ---
Took one too many pit-stop... :)

jorgenjl2:
I need some help. I have three racing cabinets hooked up with the settings below but the racers still blink a lot. What is wrong with this? The m2network.ini is simple (pc 1 to pc2 to pc3 back to pc1 all over rx and next port both/all 9001 for port and framesync=1) which network wise works fine but the lagfix is not working. Is RemoteHost supposed to be local host ip like below? I am pretty sure my 2 player settings I posted a few posts up worked with no blinking but now I am wondering if I had anything wrong.

Pc 1 - 192.168.0.2
—M2lagfix.ini
LocalHost=0.0.0.0
LocalPort=9000
RemoteHost=192.168.0.2
RemotePort=9001
StallDetection=1
[m2tx]
LocalHost=192.168.0.2
LocalPort=9002
RemoteHost=192.168.0.3
RemotePort=9000

Pc2 - 192.168.0.3
—m2lagfix.ini
[m2rx]
LocalHost=0.0.0.0
LocalPort=9000
RemoteHost=192.168.0.3
RemotePort=9001
StallDetection=1
[m2tx]
LocalHost=192.168.0.3
LocalPort=9002
RemoteHost=192.168.0.4
RemotePort=9000

Pc 3 - 192.168.0.4
—m2lagfix.ini
[m2rx]
LocalHost-0.0.0.0
LocalPort=9000
RemoteHost-192.168.0.4
RemotePort=9001
StallDetection=1
[m2tx]
LocalHost=192.168.0.4
LocalPort=9002
RemoteHost=192.168.0.2
RemotePort=9000

buttersoft:
This post contains two IP addresses, and the one below it is Sailorsat explaining how to config m2lagfix for them.

http://forum.arcadecontrols.com/index.php/topic,133283.msg1462123.html#msg1462123

jorgenjl2:

--- Quote from: buttersoft on December 04, 2023, 05:32:38 am ---This post contains two IP addresses, and the one below it is Sailorsat explaining how to config m2lagfix for them.

http://forum.arcadecontrols.com/index.php/topic,133283.msg1462123.html#msg1462123

--- End quote ---

EDIT: REPLACING 127.0.0.1 with each PCs local ip address (192.168.0.2 on pc 1, etc) for each time 127.0.0.1 is below, it runs and it appears pc 1 and pc3 have no flashing cars but pc 2 does still for some reason (I may have started the game with pc2 if it matters). I will test some more or see if I have a typo in my code.

Hmm this doesn’t seem to work for 3 players but I may have something wrong. Here is what I have. I assume it’s a ring back to the beginning. Do the ports need to change for 3 players?

Pc 1 - 192.168.0.2
—M2network.ini
[Network]
RxPort=9001
NextIP=127.0.0.1
NextPort=9002
FrameSvnc=1

—M2lagfix.ini
[m2rx]
Localhost=0.0.0.0
LocalPort=9000
Remotelost=127.0.0.1
RemotePort=9001
StallDetection=1

[m2rx]
LocalHost=127.0.0.1
LocalPort=9002
RemoteHost=192.168.0.3
RemotePort=9000

Pc 2 - 192.168.0.3
—M2network.ini
[Network]
RxPort=9001
NextIP=127.0.0.1
NextPort=9002
FrameSync=1

—M2lagfix.ini
[m2rx]
LocalHost-=0.0.0.0
LocalPort=9000
RemoteHost=127.0.0.1
RemotePort=9001
StallDetection=1

[m2tx]
LocalHost=127.0.0.1
LocalPort=9002
RemoteHost=192.168.0.4
RemotePort=9000

Pc 3 - 192.168.0.4
—M2network.ini
[Network]
RxPort=9001
NextIP=127.0.0.1
NextPort=9002
FrameSync=1

—M2lagfix.ini
[m2rx]
LocalHost=0.0.0.0
LocalPort=9000
RemoteHost=127.0.0.1
RemotePort=9001
StallDetection=1

[m2tx]
LocalHost=127.0.0.1
LocalPort=9002
RemoteHost=192.168.0.2
RemotePort=9000

jorgenjl2:
The first two times I played with the new lag fix settings above (with the local ips instead of 127.0.0.1), the game started in 3 player mode but just racer 2 had flickering. The third and fourth time (exit game but no reboot and same settings) there was no flickering at all for any racer. Does this have to do with who starts the race or something? I will have to test more.

Navigation

 Message Index

Go to full version