Main > Main Forum

Experience with Modular Control Panels

<< < (2/4) > >>

telengard:
I also screw down my modules for stability.  With a handheld power screwdriver it doesn't take long at all to do a new setup.  I also use RJ 45 cables for my modules since you only need to use 2 hands to insert remove a module.  I had used molex connectors at one point but you need to have 3 hands to do those.   :)

I'm a little too rough w/ joysticks to not have them locked down w/ threaded screws.  I also didn't want to "baby" anything so having things be really tight and locked down eliminates that.

My setup is in my signature if you are looking for examples.

~telengard

weisshaupt:
You may want to look in the wiki and my project thread (click on my WWW link)  at my take on the modular panels. I got them to work very well using a Doc-like slot and a velcro "shoelace" approach.  No slop at all in the panels, and my 6 year old son can change them out.  The doors that hold the the CCFL lights, have a little more slop than I like, but you don't notice it while playing.. I have also done a sketchup that I think has a better mounting mechanism for them, especially if you are NOT going to side light them like I did.

Modular panels are the way to go in my opinion - No reaching around other controls.  put the button on either side for the south paws,  and add more controls as you want/can afford them.

I also used Doc's RJ45 method- it rocks.

NoOne=NBA=:

--- Quote from: telengard on March 13, 2008, 07:52:44 pm ---With a handheld power screwdriver it doesn't take long at all to do a new setup.
--- End quote ---

I'd second that.
I used furniture bolts on my panels, that have a big flat head, with a hex-shaped hole on them.
With a hex bit in the screwdriver, I can swap out a panel in under 30 seconds.



--- Quote ---I had used molex connectors at one point but you need to have 3 hands to do those.
--- End quote ---

My swappable panels used 9-pin DIN connectors.
You need 3 hands for those too.
Pretty much anything that has wire at both ends will need 3 hands to work.

Paul Olson:
Mine is also held down with screws and connected with cat5. Swap times could be faster, but it really is not much of an issue. Maybe adds a minute (or 2 if I'm slow) to the swap. I would not give up the feel of a completely secure panel for a faster swap, it is not even a consideration.

Having the right controls makes the experience. I finally found a joystick that I can play Donkey Kong with and I love playing my favorite game again. I am using a wico 4-way, and I should have my nintendo stick going next week. My scores are in the 80,000s now, I don't think I got over 20,000 with any of my other sticks. Hopefully I will start getting past the 3rd elevators with the nintendo stick.

Tron is only Tron with the real stick, and I would not even want to play it without it.

Modular is the only choice for me, and I think it is a good choice for some people. It will be too much work for most people probably. There are a LOT of panels that need to be made if you want the correct controls for a lot of games. Storing all of the panels definitely takes up some space. There are some glitches every once in a while when you swap, and it requires restarting mame or sometimes the computer. All minor annoyances compared to the benefits of modular.

My www link goes to my project post if you want to take a look. I am hoping to really get some use out of my panel by finishing some more panels ,so it might be a better example before too long.


Basically, if you want accurate controls and you do not mind the extra work and hassle; you will really enjoy a modular panel.

Paul

TheShanMan:
If you haven't considered swappable panels, you might give thought to that as well. The concept is similar to modular, but instead of hooking in several pieces each time, you're only hooking in one. I have designed a very secure locking system for my metal cp that I'm very happy with. Basically the overall cp has a big rectangular hole with a slot along the bottom edge for locking in the bottom edge and 3 very small bolts sticking up along the top edge that lock in the top edge with tiny acorn nuts. So the end result is a flush cp with 3 acorn nuts out of the way along the top. (One of these days I need to create a project page so I can post some pictures)

I just completed my main 2 player panel - 2 competition 8 way joysticks with 6 buttons each. Soon I will do a trackball + spinner panel as well as a 1 player mag stick plus panel (4 way/8 way switchable). Ultimately when I get my hands on a tron style stick I will split my trackball/spinner panel into 2 panels - a trackball panel (and maybe I'll pick up a 2nd trackball for playing marble madness with my son) and a panel for spinner games and tron (spinner plus tron stick). I also ultimately plan to have an analog stick panel (for games like star wars and paper boy), a light gun panel, and a steering wheel panel. All of these panels plug in with a DB37 connector.

Also, for playing 3 or 4 player games I made 2 wood lap panels with a competition stick and 3 buttons, which have a long cord and plug into DB9 connectors mounted on the bottom of my panel.

So far I love my design. Storage is the only issue - I think I'll create or buy some sort of a storage box for them. The only real duplication of controls is with the buttons, but they were only $1.35 each so who cares.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

Go to full version