Main > Software Forum

Can someone tell me if its Mame / MaLa / Fatfingers Pluggin, or my U360's Issue

<< < (2/5) > >>

fatfingers:

The joystick is completely mapped before MAME starts.  Try uninstalling the plugin from MaLa and see if the same issue still happens.  You have to go about the debugging process slowly and methodically.  If the problem still happens without the plugin, then what about if you start MAME and the game in question from the command line?

mrclean:
I think I may have figured it out.. its mapping the wrong 2-way map.. its mapping a 2-way up and down map restriction instead of a left right map.. which is why within mame if i hit TAB i can hit up and down and it will let me assign those as the inputs. How do i fix this? I think I just need to edit / or delete a MAP file / ugc. file ? Where is that map thats causing me these issues?>

mrclean:

--- Quote from: kegger on January 29, 2008, 11:09:25 pm ---Have you created a file called "umapper.log"? This should tell you what is going on when the plugin tries to load a map for a game. I would first make this file and see what it says
then go from there. I am using Mala and the same plugin with no issues but I haven't tried those games either but I will give them a shot tomorrow and post the results.

--- End quote ---

EVENT: Game start (ROM: 'bubbobr1', CLONE OF: 'bublbobl', CONTROL: 'joy2way')

_build_mapname: Built map file name: 'C:\Program Files\mala\Maps\bubbobr1.ugc'
_file_exists: Seeing if file 'C:\Program Files\mala\Maps\bubbobr1.ugc' exists
_file_exists: 'C:\Program Files\mala\Maps\bubbobr1.ugc' does not exist
_get_mapname: did not locate rom name map file: 'C:\Program Files\mala\Maps\bubbobr1.ugc'
_get_mapname: looking for map for clone: 'bublbobl'
_build_mapname: Built map file name: 'C:\Program Files\mala\Maps\bublbobl.ugc'
_file_exists: Seeing if file 'C:\Program Files\mala\Maps\bublbobl.ugc' exists
_file_exists: 'C:\Program Files\mala\Maps\bublbobl.ugc' does not exist
_get_mapname: locating map by control type: 'joy2way'
_build_mapname: Built map file name: 'C:\Program Files\mala\Maps\2way.ugc'
_file_exists: Seeing if file 'C:\Program Files\mala\Maps\2way.ugc' exists
_file_exists: 'C:\Program Files\mala\Maps\2way.ugc' does exist
_get_mapname: located control name map file: 'C:\Program Files\mala\Maps\2way.ugc'
_file_exists: Seeing if file 'C:\Program Files\mala\Maps\2way.ugc' exists
_file_exists: 'C:\Program Files\mala\Maps\2way.ugc' does exist
_run_ultramap: command line '"ultramap.exe" "C:\Program Files\mala\Maps\2way.ugc"'
_run_ultramap: '"ultramap.exe" "C:\Program Files\mala\Maps\2way.ugc"' completed successfully

fatfingers:

A couple of things....The correct map is being applied according to the controls.ini file.  It is saying this is a 2-way game.  Should it be?

Secondly, since the 2-way map has been applied, only left and right should be registered by the joystick, and those are exactly the two directions you need to move the stick, so I'm not sure why that would be the issue?

BTW: I have that check compiled out of MAME, so I'm not able to reproduce the error for you.

mrclean:
its deffinatly the wrong map thats being sent and locking out all other "directions" of use. Its mapping an up and down restriction instead of a left / right.. which is why its not working. when I hit TAB in mame to re-assign the buttons / change the joy 1... only UP, and Down on my U360 P1 works.. which obviously i don't want Up, and down set for left and right.. how do i fix this! ?

Navigation

[0] Message Index

[#] Next page

[*] Previous page