Main > Main Forum

my new cab: retro polished timber cocktail

<< < (2/4) > >>

destr0y:

--- Quote from: notaburger on October 07, 2007, 08:56:04 pm ---i must ask, what technique, brand stain, and brand/style polyurethane did you use to get that gorgeous even color?

--- End quote ---

Its definitely all in the technique, but I've got the wife to blame/thank for that.  The stain was a Cabots Cedar one, for whatever its worth.    Make sure you sand your wood first, a nice smooth surface helps with the next stages..

The key is definitely going the whole length of the wood in a single stroke, and overlap each stroke as you go.   I applied the stain with a paintbrush, then rubbed it in with a "stain ball"..  basically, you take a bunch of cotton balls, and bunch them up in bit of cloth (in this case,  a sleeve cut off from one of my old (as in previous company) work shirts.), and tie it off with a bit of string, a rubber band or hair band so the ball is nice and tight/solid.   You use the stain ball to rub it in (hard) before it gets a chance to soak into the timber.  The stain ball acts by a) rubbing it in evenly into the grain, and b) by soaking up & redistributing any excess stain.. 

Note: the cloth around the stain ball will probably perish before you're done staining all your bits..  (you're dragging it across timber after all)..  so be prepared to make another one before you're done...

Once you're happy with the stain, varnish/wait/sand/varnish/wait/sand/varnish/wait/sand.   (ie, 3 coats of clear varnish, with a very light sand with wet&dry in between coats)

Its seriously a pain in the arse (and the upper arms), but worth the effort in the end..  just. :P

Cheers,
Brett

destr0y:

--- Quote from: leapinlew on October 07, 2007, 09:39:45 pm ---Looks good - where does the sound come out?

--- End quote ---

At the moment, through the vents :)  I've not done any permanent speaker mounting yet, because I'm not happy with the speakers I've got.   I''ve just bought a set of those new TDK tremor flat speakers to experiment with (haven't got much to report either way yet).. 


--- Quote from: leapinlew on October 07, 2007, 09:39:45 pm ---I always wonder what front end people are using to handle flipping mode and a 3 sides cabinet. What are you using?

--- End quote ---

GameEx..  to be honest though, I've not tested any of the horizontal/vertical stuff yet.  Will document what I do, when I do it though.

notaburger:
i used an old t shirt to apply mine and while it turned out better than i imagined, it still has a few streaks

i haven't applied the varnish yet, so i'll probably just start from scratch

i am good to just belt sand the whole thing and start over...right?

for the record, it's a very light stain and my wood is pine

i wish my girl knew how to stain like that...i'd be making entertainment centers and bookcases all the time

...happy birthday ma...have a shelf

Zebidee:

--- Quote from: destr0y on October 07, 2007, 11:29:05 pm ---Its seriously a pain in the arse (and the upper arms), but worth the effort in the end..  just. :P

Cheers,
Brett

--- End quote ---

From the look of your Avatar, all that works on your arms has paid off! :)

destr0y:

--- Quote from: notaburger on October 08, 2007, 09:19:20 pm ---i used an old t shirt to apply mine and while it turned out better than i imagined, it still has a few streaks

i haven't applied the varnish yet, so i'll probably just start from scratch

i am good to just belt sand the whole thing and start over...right?


--- End quote ---

You can do that, for sure..  (I freely admit I did the same thing with one of the control panel pieces when I wasn't happy with how it turned out.)..  something else to consider is to be selective with your sanding...  depends on the stain and timber you're using, but sometimes, if you have dark patches in your stain (this sentence isn't coming out right...), you can lightly sand back the darker area..  with some stains, and some timbers, it can give it a stressed / antique look & feel. 

If you do sand, the most important things:
- use continuous strokes from top to bottom of the timber, ALONG THE GRAIN.
- Use a stain ball to evenly distribute the stain...  just using a cloth (ala old shirt) doesn't cut it because the stain can accumulate in the cloth (whereas with a stain ball the cotton balls can soak it up)

Like I said, I'm no expert with staining, I'm sure there are better ways of doing it... but the tips the wife gave me speak for themselves.. 

Cheers,
Brett

Navigation

[0] Message Index

[#] Next page

[*] Previous page

Go to full version