Main > Main Forum
27inch Sharp inside a Lucid Flashback Cabniet!
leapinlew:
--- Quote from: rdowdy95 on July 10, 2006, 03:45:27 pm ---Thanks guys for the good replies. You guys have sold me. I will be getting a 4th piece of plywood. I will make all inside cabniet pieces one inch bigger. So instead of the original Lucid plan section that made all the widths 26" for the inside shelfs etc I will make them 27" that way the total width through a door would be 28 1/2". Thanks guys. Also since I am going with an all wood look stained in Minwax Polyshades the Honey Pine color. Look here to see:
http://www.minwax.com/products/onestep/polyshades-color.cfm
I was wondering. Everyone says go T-Molding for protection. What color of T-Molding should I use. A dark brown maybe, or possibly black what do you guys think?
Also how far do I go back with the T-Molding. I know the whole front of the cab do I do it on the very back of the cab too? Or should I stop the tmolding rigth at the top of the marquee or take it back all the way down to the cabniet top or the cabniet back top section?
--- End quote ---
Black because there will be other black sections on your cabinet. The bezel, coin door and possibly your controls will be black.
rdowdy95:
Thanks man I didn't think of that. I will be wrapping it around the whole cabniet as well. Even down the back. Man I can't wait I am going to get the wood this weekend. I am getting this Classic Birch Plywood from Home Depot. It is very smooth as well. Won't have to sand it that much.
leapinlew:
--- Quote from: rdowdy95 on July 10, 2006, 04:42:53 pm ---Thanks man I didn't think of that. I will be wrapping it around the whole cabniet as well. Even down the back. Man I can't wait I am going to get the wood this weekend. I am getting this Classic Birch Plywood from Home Depot. It is very smooth as well. Won't have to sand it that much.
--- End quote ---
great! Don't forget to post in the project announcements and take pictures. For every person that responds on here, there are several who lurk without ever leaving a message. You could be helping someone out without even knowing it.
What I did was document the whole process as best I could and print it out. I then put the printout inside the cabinet. Although it may seem kind of boring to you, your kids may love it. I would love to have anything like that from my dad.
jfh2112:
--- Quote from: leapinlew on July 10, 2006, 04:45:35 pm ---great! Don't forget to post in the project announcements and take pictures. For every person that responds on here, there are several who lurk without ever leaving a message. You could be helping someone out without even knowing it.
--- End quote ---
This is true. This is my 1st post but I've been visiting here for nearly a year; you wouldn't believe how many threads I have bookmarked about building cabs. :)
I put a 27" Orion TV in my Lusid cab, but kept the plans the same (I added 2 2x4s underneath the monitor shelf, though). It is definitely a tight fit, but the bezel sides aren't as thin as you'd think; you also have to take into account the casing on the sides you'll want to mask or cover up. The mask is about 2 1/8" wide on the sides.
rdowdy95:
My project arcade uses 4 2x2 blocks underneath the monitor shelf with these right angle pieces (think they are called shelf brackets. Do you think this would be good for a 27inch tv that weighs 70lbs. I am just going by what my Project Arcade book says. And if you had the choice would you make it a little bit wider next time so it wouldn't be so hard putting the TV in there?
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version