Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: [1]
  
Go Down

Author Topic: Connection on monitor end  (Read 1225 times)

0 Members and 1 Guest are viewing this topic.

wfg97079

  • Trade Count: (+2)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 308
  • Last login:March 24, 2023, 10:11:50 pm
  • I'm a llama!
Connection on monitor end
« on: June 07, 2004, 08:54:45 pm »
I have a refirb wells gardner monitor, this is the type of connector that is on the monitor, where can I get a connector to fit it?
Logged

Ken Layton

  • Guru
  • Trade Count: (+1)
  • Full Member
  • ****
  • Offline Offline
  • Posts: 7061
  • Last login:October 12, 2021, 12:25:59 am
  • Technician
Re:Connection on monitor end
« Reply #1 on: June 07, 2004, 11:33:19 pm »
Mouser Electronics (www.mouser.com) part number 538-09-50-7101 (56 cents) or # 538-09-50-3101 (56 cents) for the plastic connector housing. You'll also need 6 of # 538-08-50-0106 pins (8 cents each) and crimper tool # 538-63811-2200 ($170).

You could also order the cable with connector assembly ready-to-go from Bob Roberts for around $10.
Logged

SirPeale

  • Green Mountain Man
  • Global Moderator
  • Trade Count: (+23)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 12963
  • Last login:August 04, 2023, 09:51:57 am
  • Arcade Repair in New England
    • Arcade Game and Other Coin-Op Projects
Re:Connection on monitor end
« Reply #2 on: June 08, 2004, 11:37:43 am »
You don't need *that* crimper, do you Ken?  I mean, I've seen molex crimpers go for like $20 or less.  The one that you recommended to me earlier, for example.
Logged

Ken Layton

  • Guru
  • Trade Count: (+1)
  • Full Member
  • ****
  • Offline Offline
  • Posts: 7061
  • Last login:October 12, 2021, 12:25:59 am
  • Technician
Re:Connection on monitor end
« Reply #3 on: June 08, 2004, 07:17:01 pm »
No, you don't absolutely have to have the crimper quoted in the above post. It was the only one listed in the Mouser catalog I have. There is a cheaper hand crimper that Molex/GC/Waldom makes but I don't have the number handy.
Logged

SirPeale

  • Green Mountain Man
  • Global Moderator
  • Trade Count: (+23)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 12963
  • Last login:August 04, 2023, 09:51:57 am
  • Arcade Repair in New England
    • Arcade Game and Other Coin-Op Projects
Re:Connection on monitor end
« Reply #4 on: June 09, 2004, 07:23:52 am »
It's Molex part #W-HT-1919.  Luckily I saved the email you sent me before.  Available @ http://www.mcminone.com
« Last Edit: June 09, 2004, 07:24:32 am by Peale »
Logged

fredster

  • Grand Prophet of Arcadeology
  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2267
  • Last login:February 16, 2019, 04:28:53 pm
  • It's all good!
Re:Connection on monitor end
« Reply #5 on: June 09, 2004, 11:50:56 am »
Did you read the Monitor FAQ?

Bob Roberts Sells them, but you better be ready to buy more to cover shipping.
Logged
King of the Flying Monkeys from the Dark Side
Pages: [1]
  
Go Up
« previous next »