Main > Main Forum

Any interest in original cab dimensions

<< < (60/69) > >>

Crazy Cooter:
Spriggy, I'll be able to get everything but the cp (don't have it but can see where it was).  I'll be looking for those side stencils as soon as I cut some wood...  Maybe it would be easier for me to fill in the blanks you have?  I could charge the digicam if needed.

spriggy:

--- Quote from: Crazy Cooter on September 30, 2004, 11:15:10 pm ---Spriggy, I'll be able to get everything but the cp (don't have it but can see where it was).  I'll be looking for those side stencils as soon as I cut some wood...  Maybe it would be easier for me to fill in the blanks you have?  I could charge the digicam if needed.

--- End quote ---

CC,

As you would have read on my Taito Sideart thread, the artwork is on hold due to Wade's and mine current projects (both T&F cocktails).

As I aforementioned, I'm waiting on parts for measurement.  IE CP, Rear Door Hinges, Marquee Brackets, Plastic Bezel and Bezel Brackets and Coin Door.
If your eager, you could gather these dimensions (and angles) and send them to me to assit.  I'm expecting the parts to arrive within the next fortnight!?! if your willing to wait.

As for the Taito Sideart, you could use it in it's current inaccurate state (in Wade's and my eyes anyway) as a template to cut the sides and then use it as a stencil or vinyl overlay without inaccuracy.  The main cabinet side outline on the sideart has been quoted as accurate, EXCEPT for the main large curve which is out some what.

I can not tell you what the Sideart, in it's current state, will look like if applied on an ORIGINAL cabinet.

Once the plans are completed, they will be given to Jakobud for him to use in which ever way he choses.  I will however ask him if he could attach the Sideart (when completed) to the plans so it can be used as a template and/or later used as accurate artwork (especially as the dimensions for the cabinet sides are based on the Sideart stencil for accuracy)

The plans are still at this stage.......

zorg:
just to let you know that while leeching TAFA I notice that some flyers comes with plans with dimension
this could help in putting up the plans for various cabs.

hope this helps

eg I have browsed the whole taito flyer colection and find thoses to be useable
Continental Circus
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=2832&image=2

Air Inferno
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=25&image=2

Double Dragon
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=3942&image=2

Full Throttle
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=2833&image=2

Laser Grand Prix
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=584&image=2
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=583&image=2

Midnight Landing
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=676&image=2

Operation Wolf
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=3234&image=2

Sagaia
http://www.arcadeflyers.com/?page=flyerdb&subpage=flyer&id=4187&image=2


http://www.arcadeflyers.com/flyers/taito/28013802.jpg


well know we have to leech the whole dabtabase ;) I've done taito, we just have to coordinate ourselfs and it should be doable.

Crazy Cooter:
I'll try my first attachment...

spriggy:
Good on ya CC. Thanks.

Yeh, I hadn't put on the small base yet as I haven't received dimensions and offset for it.

I'll utilise some of these dimensions to assist in completing the plans.

I find that depending on who measures their cab, some dimensions may vary upto about 1/4", as is happening in this case.  For me, that leaves no easy answer on which dimensions to use.

However, not the end of the world by any means!

We'll get these plans as close as my skills allow.

Bring it on!! :)

Navigation

[0] Message Index

[#] Next page

[*] Previous page

Go to full version