Main > Main Forum
No yoke from Ram Controls
Hoopz:
--- Quote from: Bender on January 26, 2011, 09:59:56 am ---
--- Quote from: Cananas on January 23, 2011, 05:35:59 am ---
--- Quote from: Cananas on January 22, 2011, 03:15:42 pm ---I have send an e-mail to Adam, now. Let's wait what happens (Crossed fingers).
--- End quote ---
Adam gave me a fast answer:
--- Quote ---Carlos,
After a quick look, I was able to locate your pending orders for the yoke and usb board. I will ship them to you on Monday. If there is anything else, I can certainly help. I hope that these actions will be to your satisfaction.
Adam
--- End quote ---
Let's hope that finally the yoke will arrive...
--- End quote ---
Cananas,
get the yolk yet?
--- End quote ---
I'd put money on Dave sending him yolks instead of a yoke.
Cananas:
--- Quote from: Bender on January 26, 2011, 09:59:56 am ---
--- Quote from: Cananas on January 23, 2011, 05:35:59 am ---
--- Quote from: Cananas on January 22, 2011, 03:15:42 pm ---I have send an e-mail to Adam, now. Let's wait what happens (Crossed fingers).
--- End quote ---
Adam gave me a fast answer:
--- Quote ---Carlos,
After a quick look, I was able to locate your pending orders for the yoke and usb board. I will ship them to you on Monday. If there is anything else, I can certainly help. I hope that these actions will be to your satisfaction.
Adam
--- End quote ---
Let's hope that finally the yoke will arrive...
--- End quote ---
Cananas,
get the yolk yet?
--- End quote ---
Yeeeah!!. It is coming here.
Adam provided me the tracknumber yesterday (26 january). I have called UPS today and it will arrive to Spain tomorrow. So the next week will be, finally, at home, I presume.
Bender:
--- Quote from: Hoopz on January 26, 2011, 10:02:36 am ---
--- Quote from: Bender on January 26, 2011, 09:59:56 am ---
--- Quote from: Cananas on January 23, 2011, 05:35:59 am ---
--- Quote from: Cananas on January 22, 2011, 03:15:42 pm ---I have send an e-mail to Adam, now. Let's wait what happens (Crossed fingers).
--- End quote ---
Adam gave me a fast answer:
--- Quote ---Carlos,
After a quick look, I was able to locate your pending orders for the yoke and usb board. I will ship them to you on Monday. If there is anything else, I can certainly help. I hope that these actions will be to your satisfaction.
Adam
--- End quote ---
Let's hope that finally the yoke will arrive...
--- End quote ---
Cananas,
get the yolk yet?
--- End quote ---
I'd put money on Dave sending him yolks instead of a yoke.
--- End quote ---
Star Wars Yolks! eww!!!
Cananas:
Finally it have arrived today.
The yoke works OK, but... the usb inteface not.
It does not detect the x/y movement. I tried to calibrate but no, no. The potenciometers are OK (from 0 to 2,5K -both axis in parallel, I think ->Xblack are connected with Cblack and Xbrown with Cbrown-) and the wires are also OK, even the header cable that comes with the usb interface to connect the yoke.
So I supposed the problem was on the USB interface. I tried with another potenciometer (5K ohm) (ony this was connected to the PCB). I connected to the usb interface, and the axis x and y (??) move when the potenciometer it was between 0 and 4.95k ohm.
I don't know what happens with the USB interface.
MameMaster!:
I'm pretty sure you have to adjust your usb settings via the JOYSTICK settings on your pc- not via mame.
I made the same mistake and thought that it was broken.
Give that a shot-- try calibrating it via your pc.
Good luck! :cheers:
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version