Build Your Own Arcade Controls Forum

Main => Monitor/Video Forum => Topic started by: commander on May 12, 2009, 04:44:43 am

Title: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: commander on May 12, 2009, 04:44:43 am

My hanatarex polo arcade monitor stopped working, the repairs guy who used to fix hanatrex monitors said he couldn't fix it and now i am looking for a replacement chassis (220V).I have read over the forums wei-ya and jenshinn recommended went to the jenshinn site and found two free voltage chassis one is 28" and the other 29" (http://www.jenshinn.com.tw/chassis.htm) are they both ok for my monitor. any other suggestions are welcome.

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: grantspain on May 12, 2009, 05:00:14 pm

funny you should post this as i tested the jenn shin 729 dual sync chassis and its very good indeed
bit pricey compared to others but excellent controls and a manual degauss switch on the remote as well

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: commander on May 13, 2009, 02:27:39 am

so jenn shin 729 dual sync works with 15khz tubes as is my hantarex ? and i see them listing 28" and 29" chassis for the 15khz do they really differ?

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: grantspain on May 13, 2009, 02:46:13 am

the dual sync will work with a polo 1 crt,the 28" chassis will match you crt better than the 29" but both will work
if you intend to just run 15khz games then go with the 15khz chassis
jen shinn will not normally sell just one chassis though-they like to sell a carton of 12

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: commander on May 13, 2009, 03:12:34 am

Thx for the help was thinking of buying from them directly since i live in lebanon which is in the Middle East i guess it may not be possible then. Did u buy from them directly or through others and by Pricey for the 729 equates to approximately how much . How is the 729 dual sync 15khz picture quality comparable to the polo1 which is what i have been used to.

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: Level42 on May 13, 2009, 01:04:55 pm

Here are chassis for sale, prices include world wide shipping:

http://www.grebo.eu/arcadegames/shop/index_eng.htm

Select, Monitor,Parts from the drop-down list on the top-left.

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: commander on May 13, 2009, 03:16:39 pm

Thx for the link Level42 do those chassis yoke impedance match that of the polo1 (I have it packed now and can't measure it). And are these chassis good anyone tried them ?

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: grantspain on May 13, 2009, 05:04:30 pm

someone tried one of these chassis on arcade otaku and it seems o.k
POLO 1 28"
Lh 1.49mh
Lv 24.5mh
Rh 1.6 ohm
Rv 11.0 ohm

their chassis yoke spec 25-29 inch chassie scancard, HQ
VL: 20.1 MH
HL: 1.42 MH
VR: 7.2 Ohm
HR: 1.7 Ohm

It is in the range o.k

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: commander on May 19, 2009, 06:03:51 am

Hi grantspain
I am leaning toward jenn shin dual sync chassis or maybe there 15khz chassis could u tell me where i could buy just one chassis

Title: Re: looking for a hantarex polo 28"(15khz) replacement chassis(220V)
Post by: grantspain on May 19, 2009, 04:12:49 pm

there is a dealer in the u.s(8liners) that sells the chassis but you will pay a premium,but like anything you pay for what you get
if you go for a cheaper chassis then you will probably need a 110v isolation transformer

if you are u.k based i may be able to supply you a chassis but only in july as part of my arcade show spares sales