Build Your Own Arcade Controls Forum

Main => Monitor/Video Forum => Topic started by: imtapha on August 20, 2008, 02:27:57 pm

Title: Hantarex mtc28EQ2 input configuration
Post by: imtapha on August 20, 2008, 02:27:57 pm

Hi. I have an Alpine ski 2 which has a 28inch hantarex polo that has died. I have a nos Hanterax mtc28EQ2 which has a variety of input possibilities on D-type, scart and s-video. would it be possible to wire this to my Alpine 2 and if so how? hope someone can help. pic of mtc28 below

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: grantspain on August 20, 2008, 03:01:34 pm

you can use the scart,
there is a thread at the top of the monitor page

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: imtapha on September 04, 2008, 11:32:09 am

have tried using the scart wired 4 rgb and although there is an image on screen the colours are very pale and the image has a shadow and is not very well defined. does anyone have any ideas?

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: grantspain on September 04, 2008, 03:01:59 pm

you need more than 4 wires if using the scart,follow the instructions on the thread

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: imtapha on September 05, 2008, 02:52:38 am

sorry for the confusion was being lazy wired 4 scart didnt mean 4 wires should have said wired for scart. i did follow instructions in thread and ended up with fault described

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: grantspain on September 05, 2008, 06:19:30 pm

do you have an impedence switch,maybe marked 1v or 0.75

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: imtapha on September 06, 2008, 03:10:17 am

no impedence switch

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: grantspain on September 06, 2008, 04:41:37 am

maybe try the rgb d plug,i know the tech at hantarex very well so if you wish i can ask him the pinout of that plug
i will call him on tuesday as i am off work until then

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: imtapha on September 06, 2008, 05:00:23 am

that would be great many thanks

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: imtapha on September 29, 2008, 12:09:18 pm

hi bog trotter any joy with pin outs on the d type vga input

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: grantspain on September 29, 2008, 01:42:54 pm

sorry mate i had completely forgot,will do tomorrow

Title: Re: Hantarex mtc28EQ2 input configuration
Post by: grantspain on October 01, 2008, 05:50:58 am

o.k there are 2 versions of this,1 for the u.s market and 1 for europe
europe pinout
1-ground
2-n/c
3-red
4-green
5-blue
6-n/c
7-n/c
8-horizontal(comp) sync
9-vertical sync

u.s version
1-ground
2-comp sync
3-blue
4-green
5-red
6,7,8,9-ground