Build Your Own Arcade Controls Forum
Main => Monitor/Video Forum => Topic started by: gatordad on July 09, 2008, 08:36:28 pm
-
Not really arcade related but My big screen is on the fritz anyone know where to get the service manual from. Powers on for 3 seconds then shuts off, I can see the ttubes start to glow then she goes off all by herself, I pulled the back off and checked the 125v 10 fuse and it looks ok. Mitsubishi ws-65807.
Any help is appreciated.
-
Would think it was a power supply issue. Probably capacitors.
As for a manual...... TV manual can be hard to find on-line. (free)
But I found something that might help on Ebay.
Ebay Manual (http://cgi.ebay.com/MITSUBISHI-WS-55857-WS-65857-SERVICE-REPAIR-MANUAL-V17_W0QQitemZ300208504929QQihZ020QQcategoryZ71585QQcmdZViewItem)
Might at least have parts specs and numbers in it and the price is right.
-
u may obtain the service and training manuals in pdf format for 11.99 ea here :
www.service-manual.net/ashop/catalogue.php
click on "mitsu..." then enter ws-65807 in search box ;)
newer tv's have many "safety" circuits that will initiate a power down when a fault is detected .
hopefully urs has a minor problem .
BE CAREFUL . PROJECTION TV High Voltage supplies deliver slightly higher current levels than a standard crt system.
qrz
-
I bought a service manual and I am getting an error code 22. I need to look into this further.
-
Well I did alot of reading the last couple of days and it seems that these have a high failure rate on the IC's, they are pretty cheap about 25.00 for the pair, so I am going to try to replace these, as I don't think it's a power issue as she fires up but some kind of circuit protect kicks in an and shuts her down right away.
-
the manual should tell u what code 22 is referencing. look there for the fault ;)
yes, the stk's are a high failure item in the convergence .
but, i wouldn't expect such a fault to trigger a shutdown.
all mfgr's have their quirks, and this could be mitsu's .....
qrz
-
Gatordad - - I'm curious how you recently fixed your Mitsubishi WS-65807.
I have the same symptom. It powers on and only shows green LED for 3 sec then shuts off with audible relay clicks. Immediately after connecting to AC power, green LED flashes 3 times, indicating "Microprocessor has initialized and is functioning". Holding INPUT & MENU shows error code 22, indicating "Short protect circuit”.
I've searched around and read a lot about bad convergence chips, but my convergence was fine when it abruptly powered down while I was watching it. I've also read a lot about bad capacitors, which seems more likely. I got a PDF service manual and schematics off eBay for $5.39. Any advice would be greatly appreciated before I crawl in there.
Bill
-
I have a leaking - bad capacitor on the middle board , I have not ordered a replacement yet, so it's just sitting there collecting dust for the moment, I have no idea if that the only thing wrong yet. I have not had the time to get to it yet. It's not my primary tv so no rush on my part. I figure its worth at least 50 dollars in replacement parts before I give up. I was quoted 400-500 from a service tech to fix it. For that much I would sink my money into a new lcd replacement set.
I don't think I would buy another Mitsubishi after paying 3200.00 and having this set for only 7 years with very low hours (I don't watch that much tv) and its goes out like that to say the least is extremely frustrating.
Best of luck
-
Thanks Gatordad - I was in a similar state of mind with this old set that served me well for 7 years.
Then I got some ambition and after some browsing and probing, I found that I had 2 bad convergence ICs that blew 2 on-board fuses. I've replaced all the parts for $50 (I hit your $ threshold already). The set now works but needs a major convergence adjustment. Also, the IR remote control didn't work when I put it back together. I'm trying to figure that out now and its very frustrating.