Build Your Own Arcade Controls Forum
Main => Buy/Sell/Trade - non-retail => Topic started by: SithMaster on March 20, 2007, 04:05:16 pm
-
Looking for offers on the following (note prices do not include shipping send me an address and I will send you a quote):
6 red top joysticks - $10 for all
1 black handle competition joystick complete - $ 4
10 coin mechs mostly metal i think 2 are plastic (some happ brand) – $4 each
2 nintendo coin doors (one complete another no mechs but coin covers both need locks)
4 deep leaf switches button holders - $3 each
2 buttons for above one green one black short kind
1x nintendo joystick for parts
1 power assembly partial? i also have one from a stripped midway with a cut power cord
2x metal grilles
1 coin mech that is missing the switch
1 street fighter metal cp. the cpo is in so so shape (duct tape on the front fraying on the sides will get a better pic if interested, it has the wood bar on the bottom edge in decent shape) - $20 shipped (or around it depending on distance from me).
I also have a couple of metal control panels that are in medicore condition. they have remenants of their cpos and none look like they have been modified except for one but its just a cpo covering the button holes. some are two player (mostly fighters) and the others are single player that have player one and two button holes and left right friendly button placement. they all have rust and one has the plexi still on but it has a crack where a bolt would be to hold it in place. these are not pictured but im looking for 5 each plus shipping and pics will be available this weekend weather permitting.
Here are pics of most of the items and i apologize for the bluriness.
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004521.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004526.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5000180.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5000181.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004519.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004518.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004516.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004523.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/doorfront.jpg)
i also have a dk bezel that ill try and get a pic for as well. im looking for offers on most of the stuff. thanks.
edit also im looking for a konami 4 player cab. it doesnt need to have boards or anything, just to be in decent shape and in NJ.
-
bump?
-
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004778.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004777.jpg)
(http://i24.photobucket.com/albums/c33/Vampirelord113/S5004776.jpg)
some more parts. for the door im looking for 20 shipped and for the midway parts 6 plus shipping.
-
Is that an over/under top door? and do the mechs work? It looks like there is no graphic in the coin button but that's just a piece of plastic with black text usually right?
-
Is that a Taito control panel that the SF CPO is on?
-
Is that an over/under top door? and do the mechs work? It looks like there is no graphic in the coin button but that's just a piece of plastic with black text usually right?
i looks like it could be from an over/under (most likely is) but i was going to us it as is for a project. the inserts for 25 cents are just pieces of paper so you could open the red buttons up and put your own in. the buttons arent the same size as an over/under door i have for my cab currently so im not 100% certain if itd work with other door frames. there is only one mech in it now but i will put another inside it and test to make sure they work. they should be for quarters though.
Is that a Taito control panel that the SF CPO is on?
it could be. is there any way for me to find out? (check pics on klov or measure it and compare?). last time i measured it the cp was about 23 inches across.
-
Is that a Taito control panel that the SF CPO is on?
it could be. is there any way for me to find out? (check pics on klov or measure it and compare?). last time i measured it the cp was about 23 inches across.
I can measure up one of mine for comparison. I'll have to bring it to work with me tommorrow.
I am going to restore my Taito cab to Jungle king, but it would be nice to have a sfII layout CP I could just pop on occasionally. I have a Qix panel I was going to modify, but this would be much easier.
-
Sith--pm sent concerning the midway coin door parts.
-
I'll trade for the Competition (and that metal balltop stick beside it also if it fits with the Competition)
if you see anything from my trade items list:
http://forum.arcadecontrols.com/index.php?topic=61842.0
-
I'll trade for the Competition (and that metal balltop stick beside it also if it fits with the Competition)
if you see anything from my trade items list:
http://forum.arcadecontrols.com/index.php?topic=61842.0
The balltop stick is for a wico base. It will fit into a wico microswitch joy, but I don't think it works in a competition.
-
If you measure that door and find that it's 6 1/2" wide by 9 1/2" tall with the hinge being just a hair over 7 1/2" then I'll take it. PM me to figure out how I can pay you, Paypal?
-
In the process of getting back to everyone.
-
I'd like to see pics of your metal panels
-
ill try to get pics of everything requested for this weekend.