Build Your Own Arcade Controls Forum

Main => Main Forum => Topic started by: Turnarcades on December 20, 2006, 07:03:09 pm

Title: Minipac keeps timing out - can't program it!!
Post by: Turnarcades on December 20, 2006, 07:03:09 pm

I seriously, urgently need some quick help!!!!

I've just had two PS/2 Minipacs from Ultimarc. I set one up on one machine, then programmed it using the iPac utitlity program, so that the buttons are mapped to keys I prefer (like tab, Enter etc.).

This worked fine on my other machines, but for some reason, this one refuses to program!

I've upped the timeout period to ten seconds, as I found sometimes the other machines timed out and only worked at around 6 or 7 seconds, but this one just refuses to work. Anything I can do?

Title: Re: Minipac keeps timing out - can't program it!!
Post by: postalp123 on December 20, 2006, 08:30:02 pm

It's a shot in the dark, but try this:

1) Go into Device Manager in windows, and Uninstall ALL of your USB ports (Do not worry, they will all re-install on their own on next boot)

2) After doing the above step, then download this (http://ultimarc.com/Ipacfix.reg) and double click on it.

When my I-pac4 would give out, I would do that procedure.

Goodluck.

Title: Re: Minipac keeps timing out - can't program it!!
Post by: Turnarcades on December 21, 2006, 02:58:12 am

Will that work though? My ipac is the PS/2 (keyboard socket) version, not the USB version.

Title: Re: Minipac keeps timing out - can't program it!!
Post by: Flip_Willie on December 21, 2006, 08:39:57 am

 No, I highly doubt Postalp123's suggestion will help if it is a ps/2 connection. 

 However, I would advise you to check and make sure that you have the ps/2 cord in the right sockect on the mini pac and in the correct socket on the motherboard.  ( Don't use the Mouse PS/2 slot on the motherboard. ) Then re-boot the pc.

  Yes, I know, very simple suggestions that you have probably already checked.  But if you plugged either end of the ps/2 cable in incorrectly, it won't work. Then again, it wouldn't work period.

Just as it is,
Flip Willie

Title: Re: Minipac keeps timing out - can't program it!!
Post by: postalp123 on December 21, 2006, 08:44:41 am

Quote from: samshaw946 on December 21, 2006, 02:58:12 am

Will that work though? My ipac is the PS/2 (keyboard socket) version, not the USB version.

(Smacks Forehead) Sorry, didn't see the PS2 reference, it was late when I read that last night.

Title: Re: Minipac keeps timing out - can't program it!!
Post by: Turnarcades on December 26, 2006, 10:36:26 am

Thanks for the advice, but it turned out too be some sort of software issue. I plugged it into an identical PC I'd already used in another arcade and it programmed straight away.

I've e-mailed Ultimarc about the issue as the timeout delay seems to cause some problems it seems, so maybe it's something they can work on.

Title: Re: Minipac keeps timing out - can't program it!!
Post by: miles2912 on December 26, 2006, 03:38:10 pm

My usb mini-pac looses programming every time the pc is re-booted or the cab is turned off.  I have 2 usb slots on the pc and I have tried them both.  What I do know is just have the programmer in start up and I hit program everytime the pc boots.  If someone has a permanent fix I hope they post it.

D-