Build Your Own Arcade Controls Forum
Main => Everything Else => Topic started by: fastredpacman on June 17, 2006, 07:50:34 pm
-
Any one have any ideas how to remove tint especially in the back where the window defroster is without damaging it?
-
Any one have any ideas how to remove tint especially in the back where the window defroster is without damaging it?
Razorblade
For the old school :)
Or a heat gun.. heat, peel, repeat..
-
Any one have any ideas how to remove tint especially in the back where the window defroster is without damaging it?
without damaging the defogger? or damaging the tint?
Take a razor blade to the glass and just peel away the tint. Cut between the defroster lines if you're really worried about it, but you shouldn't do any damage.
You can't save tint... I doubt that is what you were saying, but just in case... that tint is ruined... you can't take it off without damaging it.
-
I think the defroster lines are what he's concerned about. They are basically stuck on to the window, and a razor blade might cut or damage them.
Let me know how it goes Fast, I need to remove my tint too.
-
I think the defroster lines are what he's concerned about. They are basically stuck on to the window, and a razor blade might cut or damage them.
Let me know how it goes Fast, I need to remove my tint too.
Heat gun
It peels right off.. seriously
-
I was worried about the lines not the tint. Have any of you ever tried other methods other than a heat gun?
-
the best method is really using the heat gun o n
the outside of the window (get a friend to help you),
peel from the inside,
starting at the corners with either a hardcard or
a plastic putty trowel.
once you get a good lift, it shouldnt take you more
than 10 minutes to get it done with your fingers.
-
I was worried about the lines not the tint. Have any of you ever tried other methods other than a heat gun?
Yes, ive used "glue removers" for tint, razor blades, sand papers, and heat guns..
Heat guns work the best.. Close second, is razors + Glue removers (but) = Messy as hell
-
just buy a new car insted
-
just buy a new car insted
You are f:censored: nuts but at least :laugh2:
-
no no no.... Heat gun method leaves LOTS of glue behind typically.
Try this:
Get industrial grade ammonia cleaner at the hardware store. And a roll of saran wrap from the grocery store.
On a hot sunny day, spray the ammonia on the window film from the inside wetting the entire surface.
Working quickly, smooth saran wrap over the ammonia trapping it against the film.
Leave window with saran wrap and ammonia in direct sunlight for at least a hour.
Then SLOWLY peel the tint and saran wrap together.
Usually both layers of tint {tint layer and glue layer} will peel off almost completely in one piece this way, and no razor blade damage.
-
no no no.... Heat gun method leaves LOTS of glue behind typically.
Try this:
Get industrial grade ammonia cleaner at the hardware store. And a roll of saran wrap from the grocery store.
On a hot sunny day, spray the ammonia on the window film from the inside wetting the entire surface.
Working quickly, smooth saran wrap over the ammonia trapping it against the film.
Leave window with saran wrap and ammonia in direct sunlight for at least a hour.
Then SLOWLY peel the tint and saran wrap together.
Usually both layers of tint {tint layer and glue layer} will peel off almost completely in one piece this way, and no razor blade damage.
Yeah, it leaves some glue.. you can get the glue off really easy with the tint glue removal stuff..
-
no no no.... Heat gun method leaves LOTS of glue behind typically.
Try this:
Get industrial grade ammonia cleaner at the hardware store. And a roll of saran wrap from the grocery store.
On a hot sunny day, spray the ammonia on the window film from the inside wetting the entire surface.
Working quickly, smooth saran wrap over the ammonia trapping it against the film.
Leave window with saran wrap and ammonia in direct sunlight for at least a hour.
Then SLOWLY peel the tint and saran wrap together.
Usually both layers of tint {tint layer and glue layer} will peel off almost completely in one piece this way, and no razor blade damage.
hmmmmm.......... breathing ammonia fumes inside a hot car you forgot to mention the part where he's supposed to keep the windows rolled up and it's best to do it when it's close to 100 degrees outside too.........
-
no no no.... Heat gun method leaves LOTS of glue behind typically.
Try this:
Get industrial grade ammonia cleaner at the hardware store. And a roll of saran wrap from the grocery store.
On a hot sunny day, spray the ammonia on the window film from the inside wetting the entire surface.
Working quickly, smooth saran wrap over the ammonia trapping it against the film.
Leave window with saran wrap and ammonia in direct sunlight for at least a hour.
Then SLOWLY peel the tint and saran wrap together.
Usually both layers of tint {tint layer and glue layer} will peel off almost completely in one piece this way, and no razor blade damage.
Yeah, Alot of tinting places just use windex and a razor. I didn't know about the saran wrap, cool tip.