Build Your Own Arcade Controls Forum

Main => Monitor/Video Forum => Topic started by: pirateremain on May 24, 2005, 04:07:29 am

Title: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: pirateremain on May 24, 2005, 04:07:29 am

Hello my friends,

Title: Re: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: dabone on May 24, 2005, 07:47:13 am

Yeah, buy a video amp from ultimarc.

Your problem probally is that the video card only outputs .7v on the sync and the monitor expects 5v.

Or you might need to bulid a circuit to combine your sync.



So you need a video amp.


(Or at least a sync amp and combiner)

You can use the video amp only.
http://www.ultimarc.com/vidamp.html

or a jpac that has the amp built in (It also has sync protection to keep non 15k signals from reaching your monitor)


Later,
dabone

Title: Re: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: pirateremain on May 24, 2005, 09:06:40 am

Ohh thankkss your are my rescuer.  ;D 

But I can damage the monitor with connect to AVga with my arcademonitor without jpad?

AVGA always out 15hz?? then J-pad isn't need   :o ?? or you advise me buy J-pad or video amp??  ???

I think connect buttons with hackpad but... It's better buy J-pad and all problems disapear??

Thanks for all my friends

See you soon,
PirateRemain

Title: Re: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: dabone on May 24, 2005, 09:16:31 am

Some monitors can handle the lower voltages of the avga card, some require a amp.

And no, you wont damage your monitor with the avga only.


Later,
dabone

Title: Re: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: IntruderAlert on May 24, 2005, 09:56:34 am

I thought you were supposed to use the Hantarex monitors with just the ArcadeVGA's 1v

also, aren't you supposed to just combine H sync and V sync for composite sync on the ArcadeVGA without building a circuit?

Title: Re: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: pirateremain on May 24, 2005, 10:39:57 am

Yes I supposed this I connect Vsync and Hsync without any circuit.  :((uff my english ... more teoric classes.. excuse me) ;D


I only have:

1- R
2- G
3- B
4- Gronund
5- Vsync (no cable

Title: Re: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: dabone on May 24, 2005, 11:48:36 am

Yes just connect the horzontial and vertical syncs together.


Later,
dabone

Title: Re: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: MonitorGuru on May 24, 2005, 12:06:36 pm

Run the combined H+V sync wire to both pins 5 and 6 on the monitor.

E.g.

13 + 14 on the VGA card, combine into one wire (as you already have)
then
connect the one wire to both pins 5 and 6 on the monitor.

If this doesn't work, then separate them and run one wire from pin 13 to pin 5 (mon) and 14 to pin 6 (mon) or vise-versa.


Also, you might want to connect the other ground connectors on the video card to pin 4 on the monitor.  There might be a difference in ground between RGB signal ground and Sync ground.  Connect them all together (pin 6,7,8, plus pin 5, 10 (also grounds) AND the shield ground from the connector itself (wire braides inside cable) into pin 4 of the monitor.   Do this only if the fix above doesn't help.

Title: Re: Hantarex Polo Vertical Image Scroll not solved in lasts post :-(
Post by: pirateremain on May 24, 2005, 03:29:33 pm

Yes, It's solved!!! LOL  ;D  ;D  ;D  ;D in effect 13 and 14 sync for the monitor H.S comp.. and another problem with the vga cable esquem.. this is a fromt image of the pings and I think this is a back image... the 13 ping Vsincy not connect correct   :angel: sorry

Thanks for all, your are the bests!!
Pirateremain