The NEW Build Your Own Arcade Controls
Main => Driving & Racing Cabinets => Topic started by: jackiabu on November 13, 2018, 10:15:40 am
-
HI
i try to setup my ferrari thrustmaster 458 on Supermodel-UI Sega model 3. so far no success.
left and right on the wheel respon good but no gas or breaks , i try allmost evrey thing on the setting menu under RACE.
by the way, the wheel playing good all other racing mame games on my cab. :hissy:
-
Supermodel UI is no longer supported so I would suggest you to run and setup M3 games with a cmd file
-
Supermodel UI is no longer supported so I would suggest you to run and setup M3 games with a cmd file
thanks for this info....but its make no sense that all button on the wheel respon good and can mapping. only gas i need to mapping. it's something that i missing :dizzy:
-
When debugging hardware/software you shold proceed in an additive way more than subtractive. This means that you need to start from the slimmest hardware and software. In this case hardware is you wheel (ok) software is UI+emulator. Remove the UI.
-
I've had issues before where a new build of Supermodel wouldn't respond to my gas and brake inputs when I was trying to configure them with my pedals, even when I specifically used the command for dinput devices (supermodel -config-inputs -input-system=dinput) when I was configuring all my settings. I can't remember how I fixed it now, I think I either just copied and pasted a config file across from an older Supermodel with all my wheel settings in.
-
I've had issues before where a new build of Supermodel wouldn't respond to my gas and brake inputs when I was trying to configure them with my pedals, even when I specifically used the command for dinput devices (supermodel -config-inputs -input-system=dinput) when I was configuring all my settings. I can't remember how I fixed it now, I think I either just copied and pasted a config file across from an older Supermodel with all my wheel settings in.
I really appreciate if you remember ::) no luck on CMD allso...
-
Try seeing if you can get Supermodel to recognise the gas and brake axes in the first place. I explained how to do this to someone else on the Supermodel forum some time ago, you can read it here: https://www.supermodel3.com/Forum/viewtopic.php?f=3&t=49&start=530#p11331 (https://www.supermodel3.com/Forum/viewtopic.php?f=3&t=49&start=530#p11331)
-
Try seeing if you can get Supermodel to recognise the gas and brake axes in the first place. I explained how to do this to someone else on the Supermodel forum some time ago, you can read it here: https://www.supermodel3.com/Forum/viewtopic.php?f=3&t=49&start=530#p11331 (https://www.supermodel3.com/Forum/viewtopic.php?f=3&t=49&start=530#p11331)
OK thanks . but what this parameter means -config-inputs ? i get only config folder in cmd, and there is ini file. how do i get to the configure inuputs in the cmd?
-
I am struggling with a similar issue trying to interface the Immersion FFB board to Supermodel. The M2 emulator works fine on both gas & brake pedal, so I know it may be done but the manual -config-inputs calibration method doesn't seem to help and every combination of input I've tried so far doesn't work, I've tried builds 502 and the current with the same results.
What is the difference between the M2 emulator input routine and the Supermodel? I wonder.
I need to check some more but I swear that the M2 emulator switches gas/brake after set up.
Any insight appreciated.
68hc11
-
I am struggling with a similar issue trying to interface the Immersion FFB board to Supermodel. The M2 emulator works fine on both gas & brake pedal, so I know it may be done but the manual -config-inputs calibration method doesn't seem to help and every combination of input I've tried so far doesn't work, I've tried builds 502 and the current with the same results.
What is the difference between the M2 emulator input routine and the Supermodel? I wonder.
I need to check some more but I swear that the M2 emulator switches gas/brake after set up.
Any insight appreciated.
68hc11
update me please, so far it's seem that no one has solved this problem ;D